This DTC is output when an open circuit or short occurs in the communication line between a rear center ultrasonic sensor (RRC sensor) and the rear center ultrasonic sensor (RLC sensor), or when a malfunction occurs in a rear center ultrasonic sensor (RRC sensor) on the rear.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AE887 | Ultrasonic Sensor (Rear Right Center) Missing Message | Rear center ultrasonic sensor (RRC sensor) lost communication | ·
Rear center ultrasonic sensor (RRC sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
If a DTC is detected again after the repair, turn the power switch on (IG) and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
If C1AE796 is output at the same time, check C1AE796 first.
Initialize the rear corner ultrasonic sensors (RL and RR sensors) and rear center ultrasonic sensors (RLC and RRC sensors).
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Symptoms | DTC Detection | |||
|---|---|---|---|---|
| C1AE687 | C1AE787 | C1AE887 | C1AE987 | |
| Symptom 1 | Not output | Not output | Not output | Not output |
| Symptom 2 | Not output | Not output | Not output | Output |
| Symptom 3 | Not output | Not output | Output | Output |
| Symptom 4 | Not output | Output | Output | Output |
| Symptom 5 | Output | Output | Output | Output |
| Result | Proceed to |
|---|---|
| Listed under symptom 1 in combination table | A |
| Listed under symptom 2 in combination table | B |
| Listed under symptom 3 in combination table | C |
| Listed under symptom 4 in combination table | D |
| Listed under symptom 5 in combination table | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
Disconnect the Q5 rear center ultrasonic sensor (RLC sensor) connector.
Disconnect the Q4 rear center ultrasonic sensor (RRC sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q5-1 (BO) - Q4-4 (BI) | Always | Below 1 Ω |
| Q5-2 (SO) - Q4-5 (SI) | Always | Below 1 Ω |
| Q5-3 (EO) - Q4-6 (EI) | Always | Below 1 Ω |
| Q5-1 (BO) or Q4-4 (BI) - Body ground | Always | 10 kΩ or higher |
| Q5-2 (SO) or Q4-5 (SI) - Body ground | Always | 10 kΩ or higher |
| Q5-3 (EO) or Q4-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear center ultrasonic sensor (RRC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL
Inspect the rear center ultrasonic sensor (RRC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear center ultrasonic sensor (RRC sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AE887 is output | B |
A
B
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL