52463
1.INSTALL REAR BUMPER PAD LH
When installing a new rear bumper pad LH, heat the rear bumper piece LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Piece LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper piece LH excessively.
When reusing the rear bumper piece LH:
Using a heat light, heat the rear bumper piece LH surface.
Remove any remaining double-sided tape from the rear bumper piece LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper piece LH surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad LH using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper pad LH has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper pad LH trying not to touch the adhesional surface.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Mark-off Line |
Align the rear bumper pad LH with the mark-off line on the rear bumper piece LH and install it.
Press the rear bumper pad LH firmly to install it.
52463B
2.INSTALL REAR BUMPER PAD LH
When installing a new rear bumper pad LH, heat the rear bumper piece LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Piece LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper piece LH excessively.
When reusing the rear bumper piece LH:
Using a heat light, heat the rear bumper piece LH surface.
Remove any remaining double-sided tape from the rear bumper piece LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper piece LH surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad LH using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper pad LH has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper pad LH trying not to touch the adhesional surface.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Mark-off Line |
Align the rear bumper pad LH with the mark-off line on the rear bumper piece LH and install it.
Press the rear bumper pad LH firmly to install it.
52462
3.INSTALL REAR BUMPER PAD (for LH Side)
When installing a new rear bumper pad, heat the rear bumper piece LH using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Piece LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper piece LH excessively.
When reusing the rear bumper piece LH:
Using a heat light, heat the rear bumper piece LH surface.
Remove any remaining double-sided tape from the rear bumper piece LH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper piece LH surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper pad has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper pad trying not to touch the adhesional surface.
| *a | Mark-off Line |
Align the rear bumper pad with the mark-off line on the rear bumper piece LH and install it.
Press the rear bumper pad firmly to install it.
52462
4.INSTALL REAR BUMPER PAD (for RH Side)
When installing a new rear bumper pad, heat the rear bumper piece RH using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Piece RH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper piece RH excessively.
When reusing the rear bumper piece RH:
Using a heat light, heat the rear bumper piece RH surface.
Remove any remaining double-sided tape from the rear bumper piece RH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper piece RH surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the rear bumper piece RH on the installation area of the rear bumper pad using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper pad has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper pad trying not to touch the adhesional surface.
| *a | Mark-off Line |
Align the rear bumper pad with the mark-off line on the rear bumper piece RH and install it.
Press the rear bumper pad firmly to install it.
52462C
5.INSTALL REAR BUMPER PAD RH
When installing a new rear bumper pad RH, heat the rear bumper piece RH using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Piece RH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper piece RH excessively.
When reusing the rear bumper piece RH:
Using a heat light, heat the rear bumper piece RH surface.
Remove any remaining double-sided tape from the rear bumper piece RH.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper pad RH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper piece RH surface.
| *a | Mark-off Line |
|
Primer |
Apply primer to the rear bumper piece RH on the installation area of the rear bumper pad RH using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper pad RH has been attached.
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper pad RH trying not to touch the adhesional surface.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Mark-off Line |
Align the rear bumper pad RH with the mark-off line on the rear bumper piece RH and install it.
Press the rear bumper pad RH firmly to install it.
76829A
6.INSTALL BACK DOOR GARNISH RETAINER
Install the back door garnish retainer.
Use the same procedure for the RH and LH side.
52453
7.INSTALL REAR BUMPER CENTER GUARD (for Separate Type)
Attach the guide and claw to install the rear bumper center guard.
|
Install in this Direction | - | - |
Install the 4 outside moulding retainers as shown in the illustration.
52461
8.INSTALL REAR BUMPER CENTER PAD (except Separate Type)
When installing a new rear bumper center pad, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Cover | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper cover excessively.
When reusing the rear bumper cover:
Using a heat light, heat the rear bumper cover surface.
Remove any remaining double-sided tape from the rear bumper cover.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper center pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new rear bumper cover surface.
Apply primer to the rear bumper cover on the installation area of the rear bumper center pad using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper center pad has been attached.
| *a | Mark-off Line | - | - |
|
Primer | - | - |
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper center pad trying not to touch the adhesional surface.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Align the 3 rear bumper center pads with the mark-off line on the rear bumper cover and install them.
Press the rear bumper center pad firmly to install it.
| *a | Mark-off Line | - | - |
52151E
9.INSTALL REAR BUMPER BAR
When installing the rear bumper bar, heat the rear bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Rear Bumper Cover | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper cover excessively.
When reusing the rear bumper cover:
Using a heat light, heat the rear bumper cover surface.
Remove any remaining double-sided tape from the rear bumper cover.
Wipe off any tape adhesive residue with cleaner.
Installing the rear bumper bar with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new rear bumper cover surface.
Apply primer to the rear bumper cover on the installation area of the rear bumper bar using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear bumper bar has been attached.
| *a | Mark-off Line | - | - |
|
Primer | - | - |
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Remove the release paper of a new rear bumper bar trying not to touch the adhesional surface
After removing the release paper, keep the exposed adhesive free from foreign matter.
Align the rear bumper bar with the mark-off line on the rear bumper cover and install it.
Press the rear bumper bar firmly to install it.
| *a | Mark-off Line | - | - |
81920
10.INSTALL REFLEX REFLECTOR ASSEMBLY LH
|
Install in this Direction |
Attach the guide to install the reflex reflector assembly LH.
Install the screw.
81910
11.INSTALL REFLEX REFLECTOR ASSEMBLY RH
Use the same procedure for the RH and LH side.
12.INSTALL SPRING NUT
|
Install in this Direction |
Install the 2 spring nuts.
Use the same procedure for the RH and LH side.
w/ Mudguard:
|
Install in this Direction |
Install the 2 spring nuts.
Use the same procedure for the RH and LH side.
52162A
13.INSTALL REAR BUMPER PIECE LH
|
Install in this Direction |
Attach the guide and claw to install the rear bumper piece LH.
Install the 3 outside moulding retainers as shown in the illustration.
Install the 2 screws.
52161A
14.INSTALL REAR BUMPER PIECE RH
Use the same procedure for the RH and LH side.
89348S
15.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89348R
16.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89342A
17.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89342
18.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
82182
19.INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
Attach the clamp to install the No. 2 luggage room wire.
| *A | w/ Hands Free Power Back Door | - | - |
Connect the 4 connectors.
Do not apply excessive loads to the retainer. Otherwise, it may peel off.
891B1
20.INSTALL KICK DOOR CONTROL BRACKET (w/ Hands Free Power Back Door)