89305
1.INSTALL ULTRASONIC SENSOR CUSHION SET (w/ Parking Support Brake System)
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
Install the ultrasonic sensor cushion set as shown in the illustration.
|
Install in this Direction | - | - |
89348S
2.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER
Installing the rear center ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Perform the following procedure only when replacement of a rear center ultrasonic sensor retainer is necessary.
Use the same procedure for the RH and LH side.
The following procedure is for the LH side.
Clean the rear bumper assembly surface.
Remove any remaining double-sided tape from the rear bumper assembly.
Wipe off any tape adhesive residue with cleaner.
| *a | 30 mm (1.18 in.) |
Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.
Apply primer to the rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Scribed Line | - | - |
|
Primer Application | - | - |
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.
Remove the peeling paper of the new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.
Align the rear center ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.
The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the rear bumper assembly.
Pushing force: 50 N (5.1 kgf) for 3 seconds
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Scribed Line | - | - |
89348R
3.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER
Installing the rear corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Perform the following procedure only when replacement of a rear corner ultrasonic sensor retainer is necessary.
Clean the rear bumper assembly surface.
Remove any remaining double-sided tape from the rear bumper assembly.
Wipe off any tape adhesive residue with cleaner.
| *a | 30 mm (1.18 in.) |
Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.
Apply primer to the rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Scribed Line | - | - |
|
Primer Application | - | - |
Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.
Remove the peeling paper of the new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.
Align the rear corner ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.
The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the rear bumper assembly.
Pushing force: 50 N (5.1 kgf) for 3 seconds
for LH Side:
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Scribed Line | - | - |
for RH Side:
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Scribed Line | - | - |
89342A
4.INSTALL REAR CENTER ULTRASONIC SENSOR
Use the same procedure for the RH and LH side.
The following procedure is for the LH side.
Attach the claw to install the rear center ultrasonic sensor.
When reusing the sensor, make sure that each sensor is returned to its original position.
Check that the claw is securely fitted.
|
Microphone Surface |
Do not push the microphone surface.
w/ Parking Support Brake System:
Align the connector with the protrusion of the mark when connecting it.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Protrusion of the mark | - | - |
|
Install in this Direction | - | - |
Connect the connector.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
89342
5.INSTALL REAR CORNER ULTRASONIC SENSOR
Use the same procedure for the RH and LH side.
The following procedure is for the LH side.
Attach the claw to install the rear corner ultrasonic sensor.
When reusing the sensor, make sure that each sensor is returned to its original position.
Check that the claw is securely fitted.
|
Microphone Surface |
Do not push the microphone surface.
w/ Parking Support Brake System:
Align the connector with the protrusion of the mark when connecting it.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
| *a | Protrusion of the mark | - | - |
|
Install in this Direction | - | - |
Connect the connector.
| *A | w/o Parking Support Brake System | *B | w/ Parking Support Brake System |
6.INSTALL REAR BUMPER ASSEMBLY
7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Hands Free Power Back Door)
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
8.INSTALL BATTERY HOLE COVER (for HV Model, w/ Hands Free Power Back Door)
58416K
9.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model, w/ Hands Free Power Back Door)
58410B
10.INSTALL DECK BOARD ASSEMBLY (for HV Model, w/ Hands Free Power Back Door)
891B2
11.INSPECT KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)
for HV Model:
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>OPERATION CHECK
for Gasoline Model:
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>OPERATION CHECK
12. INITIALIZE POWER BACK DOOR SYSTEM (w/ Hands Free Power Back Door)
for HV Model:
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for HV Model)>INITIALIZATION
for Gasoline Model:
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
13.PERFORM CALIBRATION (w/ Parking Support Brake System)
for Gasoline Model: