Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BACK DOOR OUTSIDE GARNISH (for Upper Side)
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377757 BACK DOOR OUTSIDE GARNISH(for Upper Side) A

EXTERIOR PANELS / TRIM  BACK DOOR OUTSIDE GARNISH(for Upper Side)  REASSEMBLY  


PROCEDURE

Hide 75741E 1.INSTALL SYMBOL EMBLEM

Hide 76823 2.INSTALL BACK DOOR GARNISH MOULDING PROTECTOR RH

HINT:

When installing a new back door garnish moulding protector RH, heat the back door outside garnish using a heat light.


Standard:
Item Temperature
Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door outside garnish:

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door garnish moulding protector RH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door outside garnish surface.





b.
B524043C01
0,0 0,0 false
V100144

Primer


Apply primer to the back door outside garnish on the installation area of the back door garnish moulding protector RH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door garnish moulding protector RH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door garnish moulding protector RH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524044C02
0.51,3.792 0.833,4.052 true 3.104,3.188 3.031,3.74 true 2.927,4.094 3.104,4.302 0.177,0.208 10 true *a 0.885,4.031 1.271,4.219 0.385,0.188 10 true *b, *c 3.042,2.969 3.354,3.167 0.313,0.198 10 false *c
*a 3.0 mm (0.118 in.)
*b Application Start Position
*c Rib


Align the 3 back door garnish moulding protectors RH with the application start position and install them as shown in the illustration.

HINT:

Press the back door garnish moulding protector RH firmly to install it.



Hide 76824 3.INSTALL BACK DOOR GARNISH MOULDING PROTECTOR LH

HINT:
·

When installing a new back door garnish moulding protector LH, heat the back door outside garnish using a heat light.

·

Use the same procedure to install the back door garnish moulding protector LH on the other side.



Standard:
Item Temperature
Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



a.

When reusing the back door outside garnish:

i.

Using a heat light, heat the back door outside garnish surface.


ii.

Remove any remaining double-sided tape from the back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the back door garnish moulding protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new back door outside garnish surface.





b.
B524045C01
0,0 0,0 false
V100144

Primer


Apply primer to the back door outside garnish on the installation area of the back door garnish moulding protector LH using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the back door garnish moulding protector LH has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new back door garnish moulding protector LH trying not to touch the adhesional surface.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



e.
B524046C01
2.74,4.073 2.531,3.74 true 0.448,3.771 0.563,3.51 false 0.438,4.115 0.75,4.313 0.313,0.198 10 false *a 2.76,4.031 2.958,4.229 0.198,0.198 10 false *b 0.552,3.323 0.865,3.521 0.313,0.198 10 false *c
*a 3.0 mm (0.118 in.)
*b Application Start Position
*c Rib


Align the back door garnish moulding protector LH with the application start position and install them as shown in the illustration.

HINT:

Press the back door garnish moulding protector LH firmly to install it.