Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model) › 2018.10–2019.09
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0378280 PARKING SUPPORT BRAKE SYSTEM(for Gasoline Model) D

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM(for Gasoline Model)  CALIBRATION  


NOTICE:

When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the parking support brake system may not operate correctly.


PRECAUTION (PROCEDURE 1)


a.

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during parking support brake system removal/installation are shown below.

For the installation location of the ultrasonic sensors, refer to Parts Location.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model)>PARTS LOCATION

Part Name Operation Adjustment Item Proceed to
Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize parking support brake system) Procedure 4
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Front bumper assembly
·

Replacement

·

Installation position of the front bumper assembly changes because of the removal and installation of the front bumper assembly


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Rear bumper assembly
·

Replacement

·

Installation position of the rear bumper assembly changes because of the removal and installation of the rear bumper assembly


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Clearance warning ECU assembly Replacement Ultrasonic sensor detection angle Procedure 2, 3
Steering angle neutral point Procedure 4
Bumper type registration
Ultrasonic sensor detection angle registration
Ultrasonic sensor
·

Removal and installation

·

Replacement


Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
An ultrasonic sensor becomes misaligned Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
An ultrasonic sensor is subjected to impact Ultrasonic sensor detection angle Procedure 2, 3
Ultrasonic sensor detection angle registration Procedure 4
Battery Cable is disconnected from the negative (-) battery terminal Steering angle neutral point*1 Procedure 4
Blind spot monitor sensor*2 Replacement Blind spot monitor beam axis confirmation (Click here)

*1: The steering sensor zero point can also be calibrated by driving the vehicle.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>INITIALIZATION

*2: w/ Blind Spot Monitor System




PREPARATION (PROCEDURE 2)


a.

Preparation

·

Digital angle gauge

·

Digital angle gauge attachment

·

Masking tape (To prevent damage)

·

A level


SST
09989-00020  


b.

Confirm levelness of floor surface.

i.

Place a bubble level on a level surface and confirm that the bubble is centered.

NOTICE:

Make sure that there is no gravel, sand, etc., and that the surface is not undulating.


HINT:

By adjusting the direction of the bubble level, it is possible to find a position where the bubble is centered.


E344401


ii.

Turn on the digital angle gauge.


iii.

Place the digital angle gauge in the same location and direction as that of the bubble level where the levelness of the surface was confirmed.

NOTICE:

Confirm that the location and direction of the digital angle gauge is exactly the same as that of the bubble level.


E345346C01
1.667,1 2.135,0.74 false 1.448,2.635 2.031,2.938 false 5.594,3.26 6.125,3.49 false 5.635,1.49 6.167,1.719 false 6.24,1.698 6.552,1.896 0.313,0.198 10 false *a 2.094,2.906 2.406,3.104 0.313,0.198 10 false *b 6.208,3.479 6.521,3.677 0.313,0.198 10 false *a 2.167,0.615 2.479,0.813 0.313,0.198 10 false *a
*a Digital Angle Gauge *b Level



iv.

Press the "ZERO" switch to memorize the zero point (perfectly level).

NOTICE:

Make sure that the digital angle gauge does not move when pressing the switch. If the digital angle gauge moves when the switch is pressed, an incorrect zero point may be memorized and it will not be possible to accurately check for levelness.



v.

Using the digital angle gauge in which the zero point (perfectly level) has been memorized, measure the angle of the floor surface at the 4 positions at the front of the vehicle and the 4 positions at the rear of the vehicle as shown in the illustration.

NOTICE:
·

Always position the digital angle gauge in the direction shown in the illustration.

·

Make sure that there is no gravel, sand, etc., and that the floor surface is not undulating.

·

When measuring the angle of the floor surface, avoid uneven areas such as joints between tiles.



HINT:

If necessary, the digital angle gauge can be placed anywhere within the specified area when measuring the angle of the floor surface for positions A, C, F and H.


E395086C01
0.313,0.25 2.917,0.448 2.604,0.198 10 false Position A and C: 4.688,0.26 6.875,0.688 2.188,0.427 10 false Position F and H: 4.75,0.75 6.938,1.177 2.188,0.427 10 false 50 mm (1.97 in.) 50 mm (1.97 in.) 0.615,4.385 1.219,4.844 0.604,0.458 10 false 250 mm (9.84 in.) 1.375,4.396 1.948,4.792 0.573,0.396 10 false 100 mm (3.94 in.) 0.385,0.792 2.573,1.219 2.188,0.427 10 false 50 mm (1.97 in.) 50 mm (1.97 in.) 4.906,4.365 5.469,4.719 0.563,0.354 10 false 100 mm (3.94 in.) 5.781,4.385 6.344,4.833 0.563,0.448 10 false 250 mm (9.84 in.) 5.375,2.438 5.885,2.688 0.51,0.25 10 false E 1.198,3.719 1.865,4.052 0.667,0.333 10 false D 0.583,3.708 0.885,4.01 0.302,0.302 10 false C 1.156,2.49 3.76,2.688 2.604,0.198 10 false B 0.615,2.51 3.219,2.708 2.604,0.198 10 false A 5.823,2.438 6.333,2.688 0.51,0.25 10 false F 5.365,3.688 5.875,3.938 0.51,0.25 10 false G 5.771,3.698 6.281,3.948 0.51,0.25 10 false H
V100155

Confirmation Area - -



vi.

Using the following worksheet, calculate the average of the measurements taken at the 4 positions in front of the vehicle, and calculate the average of the measurements taken at the 4 positions behind the vehicle. Confirm that the front measurement average and the rear measurement average are not more than approximately 0.37 degrees. Also, confirm that the front measurement average and the rear measurement average is less than 0.2 degrees.

NOTICE:

If the front measurement average and the rear measurement average are more than approximately 0.37 degrees or the difference between the front measurement average and the rear measurement average is 0.2 degrees or more, choose another work area as it is not possible to accurately check the installation angle of the sensors.


Worksheet:
E395087E01
0.594,2.271 1.156,2.75 0.563,0.479 10 false 250 mm (9.84 in.) 2.01,2.281 2.573,2.729 0.563,0.448 10 false 100 mm (3.94 in.) 4.906,2.26 5.469,2.656 0.563,0.396 10 false 100 mm (3.94 in.) 6.313,2.26 6.885,2.719 0.573,0.458 10 false 250 mm (9.84 in.) 1.125,1.698 1.677,2.167 0.552,0.469 10 false C 1.135,0.438 1.688,0.906 0.552,0.469 10 false A 1.5,0.438 2.052,0.906 0.552,0.469 10 false B 1.51,1.698 2.063,2.167 0.552,0.469 10 false D 5.823,0.427 6.375,0.896 0.552,0.469 10 false E 6.198,0.417 6.75,0.885 0.552,0.469 10 false F 5.802,1.698 6.354,2.167 0.552,0.469 10 false G 6.167,1.698 6.719,2.167 0.552,0.469 10 false H 1.646,2.969 2.563,3.417 0.917,0.448 10 false Front side 4.938,2.958 5.854,3.406 0.917,0.448 10 false Rear side 1,3.323 1.552,3.792 0.552,0.469 10 false A 2.708,3.323 3.26,3.792 0.552,0.469 10 false B 1,4.031 1.552,4.5 0.552,0.469 10 false C 2.708,4.031 3.26,4.5 0.552,0.469 10 false D 4.344,3.313 4.896,3.781 0.552,0.469 10 false E 6.031,3.313 6.583,3.781 0.552,0.469 10 false F 4.354,4.031 4.906,4.5 0.552,0.469 10 false G 6.021,4.042 6.573,4.51 0.552,0.469 10 false H 0.396,4.792 3.719,5.188 3.323,0.396 10 false (A + B + C + D)/ 4 = front measurement average 3.75,4.802 7.073,5.198 3.323,0.396 10 false (E + F + G + H)/ 4 = rear measurement average 0.344,5.729 3.667,6.125 3.323,0.396 10 false Both of the following conditions are met: 0.344,6.031 6.594,6.51 6.25,0.479 10 false - The difference between the front measurement average and the rear measurement average is less than 0.2 degrees. 0.333,6.563 6.646,7.156 6.313,0.594 10 false - The front measurement average and the rear measurement average are not more than approximately 0.37 degrees. 1.531,6.99 4.854,7.385 3.323,0.396 10 false OK: Proceed to the next step. 3.833,7 7.156,7.396 3.323,0.396 10 false NG: Choose another work area. 0.885,7.385 6.573,8.115 5.688,0.729 10 false (Front measurement average + Rear measurement average)/ 2 = Floor surface inclination 0.792,8.313 6.49,8.552 5.698,0.24 10 false After calculating the floor surface inclination, proceed to "Calibrate the digital angle gauge".


vii.

Average the front measurement average and the rear measurement average, then round the answer to 1 decimal place (E.g. 0.0927 degrees is rounded to 0.1 degrees) to obtain the floor surface inclination value.


viii.

Calibrate the digital angle gauge

Adjust the angle of the digital angle gauge until it reads the same value of the floor surface inclination, then press the "ZERO" switch to memorize the zero point (level with floor surface).

NOTICE:

Before pressing the "ZERO" switch, confirm that the digital angle gauge reading is positive if the floor angle inclination is positive, and negative if the floor angle inclination is negative.


E344822E02
0.865,1.844 1.688,1.531 true 0.802,0.958 1.698,1.385 true 4.188,2.125 6.323,2.521 2.135,0.396 10 false After calibrating, displays 90° when turned on its side 1.75,2.375 2.802,2.594 1.052,0.219 10 false Calibrating 0.604,0.885 0.958,1.052 0.354,0.167 10 false (+) 0.635,1.802 0.99,1.969 0.354,0.167 10 false (-)



c.
E345186E02
2.24,2.979 2.5,2.979 2.5,2.979 3.073,1.917 false 2.781,1.281 2.573,0.479 2.573,0.479 2.344,0.479 false 0.448,0.385 2.594,0.583 2.146,0.198 10 false Digital angle gauge attachment 1.385,2.885 2.344,3.083 0.958,0.198 10 false Masking tape

Prepare the digital angle gauge

i.

Attach the digital angle gauge attachment to the digital angle gauge.

SST
09989-00020  


ii.

Attach masking tape to the digital angle gauge attachment.



d.

Remove all luggage from the vehicle.


e.

Adjust the tire inflation pressure to the specified pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION



SENSOR HEIGHT AND ALIGNMENT INSPECTION (PROCEDURE 3)


HINT:

Check if the installation angle of each ultrasonic sensor is appropriate.


a.

Preparation

i.

Visually check that the bumper, grille and ultrasonic sensors are installed properly and are not damaged.

NOTICE:

If the bumper, grille or any ultrasonic sensor is not installed correctly, the calibration may not be able to be completed.



ii.

Check the tire pressures and adjust them if necessary.

Click hereGeneral>SPECIFICATIONS>TIRE / WHEEL>SERVICE DATA

NOTICE:
·

Ensure that the vehicle is level in an area with no wind.

·

Do not lean on the vehicle.

·

Do not do anything that may affect the level of the vehicle during the calibration, such as getting in or out of the vehicle, or adding or removing luggage.





b.

Sensor height and alignment inspection

E395088E01
5.177,0.865 5.115,0.24 5.115,0.24 5.281,0.24 true 1.792,2.385 1.948,2.385 1.948,2.385 1.948,1.833 true 5.229,1.156 5.479,0.823 5.479,0.823 5.646,0.823 true 5.229,1.615 5.5,2 5.5,2 5.667,2 true 5.167,1.938 5.167,2.531 5.167,2.531 5.333,2.531 true 1.396,1.979 1.552,1.979 1.552,1.979 1.896,1.656 true 1.521,0.927 1.677,0.927 1.677,0.927 1.896,1.135 true 1.813,0.615 1.969,0.615 1.969,0.615 1.948,0.969 true 0.083,0.042 6.198,0.24 6.115,0.198 10 false Ultrasonic Sensor Installation Location: 0.698,0.844 1.552,1.146 0.854,0.302 10 false FRC Sensor 5.354,0.177 6.219,0.406 0.865,0.229 10 false RR Sensor 1.104,0.531 1.896,0.771 0.792,0.24 10 false FR Sensor 5.74,0.75 6.646,1 0.906,0.25 10 false RRC Sensor 5.76,1.927 6.604,2.177 0.844,0.25 10 false RLC Sensor 5.417,2.458 6.917,2.688 1.5,0.229 10 false RL Sensor 0.604,1.896 1.427,2.156 0.823,0.26 10 false FLC Sensor 1.115,2.302 1.885,2.552 0.771,0.25 10 false FL Sensor


c.
E395089E01
1.094,2.771 1.198,2.771 1.198,2.771 1.458,1.26 true 2.094,2.979 3.042,3.281 0.948,0.302 10 false Sensor Height 0.01,2.688 2.458,2.885 2.448,0.198 10 false Center of Sensor

Measure the installation height of the sensors.

Standard Height (Front Bumper):
Sensor Location Sensor Height
Front Center Ultrasonic Sensor 682.0 to 768.3 mm (26.9 to 30.2 in.)
Front Corner Ultrasonic Sensor 636.7 to 723.0 mm (25.1 to 28.5 in.)

Standard Height (Rear Bumper):
Sensor Location Sensor Height
Rear Center Ultrasonic Sensor 452.3 to 646.8 mm (17.8 to 25.5 in.)
Rear Corner Ultrasonic Sensor 447.4 to 640.5 mm (17.6 to 25.2 in.)

NOTICE:

If the installation height of a sensor is not as specified, it may not be possible to measure the sensor angles correctly. If so, unload the vehicle and measure the installation height of the sensors again.


HINT:

Use the center of the sensor as the measuring point.



d.
E395090E01
1.313,0.771 1.417,0.771 1.417,0.771 1.417,1.5 true 1.948,1.083 1.823,1.083 1.823,1.083 1.76,1.698 true 2.052,2.083 1.927,2.083 1.927,2.083 1.865,1.719 true 0.031,0.688 1.271,0.896 1.24,0.208 10 true Digital Angle Gauge 2,0.99 3.25,1.344 1.25,0.354 10 true Digital Angle Gauge Attachment 2.135,2.021 3.271,2.229 1.135,0.208 10 true Ultrasonic Sensor

Using the digital angle gauge, measure the angle of each sensor.

i.

Measure the angle of the front sensors as shown in the illustration.

NOTICE:

Ensure that the digital angle gauge is flush with the face of the sensor.



ii.

Measure the angle of the rear sensors.

NOTICE:

Ensure that the digital angle gauge is flush with the face of the sensor.



iii.
E345374E03
2.385,1.333 2.5,1.49 2.5,1.49 2.646,1.49 true 2.125,1.396 2.073,1.896 2.073,1.896 1.969,1.896 true 2.469,1.24 2.563,0.698 2.563,0.698 2.688,0.698 true 1.74,0.719 1.823,0.26 1.823,0.26 1.979,0.26 true 0.104,0.094 1.125,0.281 1.021,0.188 10 false For example: 0.031,1.813 1.927,2.073 1.896,0.26 10 false Digital angle gauge attachment 2.031,0.156 3.375,0.458 1.344,0.302 10 false Digital angle gauge 2.729,0.583 3.365,0.969 0.635,0.385 10 false Horizontal line 0.885,0.719 1.563,0.99 0.677,0.271 10 false + 0.917,1.552 1.25,1.75 0.333,0.198 10 false - 2.708,1.396 3.365,1.781 0.656,0.385 10 false Ultrasonic Sensor

Confirm that the angles of the sensors are as specified.

NOTICE:

The sensor angle is the measured sensor angle subtracted from 90°.


HINT:
·

The digital angle gauge should indicate 90° when turned on its side.

·

If the face of the sensor is tilted upwards, the sensor angle will be positive.



Standard Angle (Front Bumper):
Sensor Location Installation Angle
Front Center Ultrasonic Sensor -1.8 to 4.3°
Front Corner Ultrasonic Sensor -1.4 to 4.7°

Standard Angle (Rear Bumper):
Sensor Location Installation Angle
Rear Center Ultrasonic Sensor 3.0 to 9.1°
Rear Corner Ultrasonic Sensor 4.5 to 10.6°


iv.

If the angle or height of the sensors is not as specified, confirm that the installation is correct and then perform the inspection again.




REGISTRATION (PROCEDURE 4)


a.

Preparation

i.

Confirm that the following DTCs are not output.

System Proceed to
TOYOTA Parking Assist-sensor System (Click here)
Parking Support Brake System (Click here)

NOTICE:

If DTC C1AE187, C1AE287, C1AE387, C1AE487, C1AE687, C1AE787, C1AE887 or C1AE987 are output at this point, it is not a malfunction. Proceed with the calibration.




b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Clearance Warning / Utility.

Body Electrical > Clearance Warning > Utility
Tester Display
ECU Calibration
50005 438 2535

f.

According to the display on the GTS, perform calibration.

HINT:

If "Battery or Steering Sensor" is selected, further calibration is not required. (Bumper type registration is not required.)



g.

Enter the bumper type using the GTS.

Bumper Type Value
Standard 1

HINT:

If the clearance warning ECU assembly is replaced or removed and installed, it is necessary to perform bumper type registration.



h.

Using the GTS, enter the measured sensor values.

NOTICE:

The sensor angle is the measured sensor angle subtracted from 90°.


HINT:

The digital angle gauge should indicate 90° when turned on its side.



i.

Disconnect the GTS from the DLC3.