Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (for Gasoline Model with Parking Support Brake System)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0378281 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for Gasoline Model with Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for Gasoline Model with Parking Support Brake System)  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E384449E03
0.594,0.833 1.917,1.563 1.323,0.729 10 false from Engine Stop and Start ECU 2.646,0.469 3.969,1.198 1.323,0.729 10 false ECU-IG1 NO.4*1 5.479,0.917 5.792,1.115 0.313,0.198 10 false IG 5.344,1.563 5.656,1.76 0.313,0.198 10 false H4 5.344,1.74 6.542,2.479 1.198,0.74 10 false Clearance Warning ECU Assembly 3.583,0.188 3.896,0.385 0.313,0.198 10 false *1 3.594,0.823 3.906,1.021 0.313,0.198 10 false *2 0.188,2.052 4.625,2.25 4.438,0.198 10 false *1: w/o Stop and Start System 0.188,2.365 4.625,2.563 4.438,0.198 10 false *2: w/ Stop and Start System 0.625,0.281 1.948,1.01 1.323,0.729 10 false from IG1 NO.1 Relay 5.469,1.208 5.781,1.406 0.313,0.198 10 false E 5.24,0.792 5.552,0.99 0.313,0.198 10 false 1 5.198,1.115 5.51,1.313 0.313,0.198 10 false 28

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure. (w/o Stop and Start System)


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
E309541C25
1.448,0.25 1.948,0.5 0.5,0.25 1.177,1.771 1.344,1.771 1.344,1.771 1.563,1.188 true 0.292,0.594 0.458,0.594 0.458,0.594 0.479,0.99 true 1.625,0.302 2.083,0.5 0.458,0.198 10 false H4 0.104,0.531 0.563,0.729 0.458,0.198 10 false IG 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1,1.688 1.156,1.885 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-28 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

H4-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V*1
10.5 to 16 V*2
H4-1 (IG) - Body ground Engine switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C