The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to How to Troubleshoot ECU Controlled Systems in Introduction.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
Check the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
If the display indicates a communication fault in the GTS, inspect the DLC3.
When any CAN communication system DTCs are output, perform troubleshooting on the CAN communication system first.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
Refer to CAN Bus Check for the CAN communication system.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
The ECM is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there are no malfunctions in the CAN communication system.
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output | A |
| CAN communication DTCs are output | B |
A
B
Refer to DTC Check / Clear.
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Road Test.
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>ROAD TEST
| Result | Proceed to |
|---|---|
| Symptom does not occur | A |
| Symptom occurs | B |
A
B
Refer to Symptom Simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Refer to Problem Symptoms Table.
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Data List / Active Test
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST
Terminals of ECM
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>TERMINALS OF ECM
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Refer to the road test.
Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>ROAD TEST
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Diagnostic Trouble Code Chart.
for SFI System: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for Manual Transaxle System: Click hereDrivetrain>EG62 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT