The clutch pedal stroke sensor assembly is installed to the clutch pedal support sub-assembly. It detects the clutch pedal position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P080512 | Clutch Position Sensor "A"Circuit Short to Battery | Clutch pedal stroke sensor assembly signal voltage is higher than 4.7 V for 5 seconds or more (1-trip detection logic) | ·
Clutch pedal stroke sensor assembly ·
Short to +B in clutch pedal stroke sensor assembly circuit ·
ECM |
Does not come on | DTC stored | SAE Code:
P0808 |
| P080514 | Clutch Position Sensor "A"Circuit Short to Ground or Open | Clutch pedal stroke sensor assembly signal voltage is below 0.3 V for 5 seconds or more (1-trip detection logic) | ·
Clutch pedal stroke sensor assembly ·
Open or short to ground in clutch pedal stroke sensor assembly circuit ·
ECM |
Does not come on | DTC stored | SAE Code:
P0807 |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Wait for 5 seconds or more with the ignition switch ON.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P080512 or P080514.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Clutch Stroke Sensor Voltage.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Clutch Stroke Sensor Voltage | Clutch pedal stroke sensor assembly output voltage | Min.: 0.000 V
Max.: 4.999 V |
·
0.96 to 1.04 V: Clutch pedal fully released ·
Value changes progressively (Only increase): Not depressed → Fully depressed (Clutch pedal should be operated slowly) |
- |
| Tester Display |
|---|
| Clutch Stroke Sensor Voltage |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
| *a | Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly) |
Disconnect the clutch pedal stroke sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A82-3 (VDD) - A82-1 (GND) | Ignition switch ON | 4.5 to 5.5 V |
Turn the ignition switch off.
Connect the clutch pedal stroke sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A82-2 (OUT) - A24-11 (CLS) | Always | Below 1 Ω |
| A82-2 (OUT) or A24-11 (CLS) - Body ground | Always | 10 kΩ or higher |
Connect the clutch pedal stroke sensor assembly connector.
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the clutch pedal stroke sensor assembly.
for LHD:
Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for LHD)>REMOVAL
for RHD:
Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P080512 or P080514 is output | B |
A
B
Disconnect the ECM connector.
Disconnect the clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A82-1 (GND) - A24-20 (E2CL) | Always | Below 1 Ω |
| A82-3 (VDD) - A24-19 (VCCL) | Always | Below 1 Ω |
| A82-1 (GND) or A24-20 (E2CL) - Body ground | Always | 10 kΩ or higher |
| A82-3 (VDD) or A24-19 (VCCL) - Body ground | Always | 10 kΩ or higher |
Connect the clutch pedal stroke sensor assembly connector.
Connect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG