Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A1  Short circuit in Power source circuit  


DESCRIPTION

C13A1 is stored if the power supply relay in the parking brake ECU assembly has a short circuit.

C13A1 is stored if the power switch is off and a voltage of 2.5 V or higher is applied to the IG terminal and an electric parking brake switch (integration control and panel assembly) malfunction or wire harness malfunction between the switch and ECU occurs.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A1 Short circuit in Power source circuit Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pulled to lock side with power switch off.

2.

Parking brake ECU assembly power source relay is shorted for approximately 60 seconds.


·

Wire harness or connector

·

Electric parking brake switch (integration control and panel assembly)

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13A1
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ -
Power switch on (IG) - ○
Malfunction Status Short in parking brake ECU assembly internal power source relay ○ ○
Detection Time Approximately 60 seconds Approximately 60 seconds
Trip Count 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


WIRING DIAGRAM

C307295E10
5.198,0.438 5.51,0.635 0.313,0.198 10 false IG 4.938,0.333 5.094,0.531 0.156,0.198 10 false 5 5.208,1.813 5.823,2.01 0.615,0.198 10 false LCK1 4.885,1.688 5.198,1.885 0.313,0.198 10 false 20 5.188,2.406 5.802,2.604 0.615,0.198 10 false LCK2 4.875,2.292 5.188,2.49 0.313,0.198 10 false 15 3.594,2.292 3.906,2.49 0.313,0.198 10 false 21 3.146,2.302 3.76,2.5 0.615,0.198 10 false LCK2 3.146,1.698 3.76,1.896 0.615,0.198 10 false LCK1 3.615,1.698 3.927,1.896 0.313,0.198 10 false 10 5.198,3.604 5.813,3.802 0.615,0.198 10 false REL1 4.885,3.479 5.198,3.677 0.313,0.198 10 false 19 3.625,3.479 4.115,3.688 0.49,0.208 10 false 22 3.625,4.104 4.01,4.323 0.385,0.219 10 false 23 5.198,4.24 5.813,4.438 0.615,0.198 10 false REL2 4.896,4.115 5.208,4.313 0.313,0.198 10 false 16 3.156,3.479 3.771,3.677 0.615,0.198 10 false RLS1 3.156,4.115 3.771,4.313 0.615,0.198 10 false RLS2 1.354,0.625 3.042,0.823 1.688,0.198 10 false ECU-IG1 NO. 3 1.875,2.927 3.323,3.333 1.448,0.406 10 false Lock Switch 1.865,4.771 3.333,5.219 1.469,0.448 10 false Release Switch 1.198,5.281 1.813,5.479 0.615,0.198 10 false E 0.896,5.24 1.365,5.552 0.469,0.313 10 false 15 4.667,4.865 5.125,5.063 0.458,0.198 10 false M35 4.656,5.052 6.854,5.427 2.198,0.375 10 false Parking Brake ECU Assembly 1.125,5.958 1.583,6.156 0.458,0.198 10 false G32 1.135,6.156 5.719,6.521 4.583,0.365 10 false Electric Parking Brake Switch (Integration Control and Panel Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - IG POWER SOURCE CIRCUIT)
a.
C306865C29
1.5,0.333 1.969,0.563 0.469,0.229 1.594,1.188 1.5,1.75 true 1.615,0.354 2.073,0.552 0.458,0.198 10 false M35 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 1.438,1.802 1.75,2 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Turn the power switch off.


b.

Disconnect the parking brake ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M35-5 (IG) - Body ground Power switch off Below 2.5 V


Result:
Proceed to
OK
NG




OK

2.INSPECT ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.

Remove the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))
a.

Disconnect the G32 electric parking brake switch (integration control and panel assembly) connector.


b.
C306865C33
1.458,0.313 1.948,0.531 0.49,0.219 1.635,1.396 1.406,1.74 true 2.365,1.333 2.635,1.344 true 1.781,1.365 2.042,1.708 true 2.198,1.365 2.531,1.708 true 1.552,0.333 2.01,0.531 0.458,0.198 10 false M35 0.063,0.094 0.375,0.292 0.313,0.198 10 false *a 2.708,1.26 3.302,1.458 0.594,0.198 10 false LCK1 1.25,1.781 1.844,1.979 0.594,0.198 10 false LCK2 1.938,1.771 2.552,1.969 0.615,0.198 10 false REL2 2.458,1.771 3.073,1.969 0.615,0.198 10 false REL1
*a Front view of wire harness connector
(to Parking Brake ECU Assembly)


Disconnect the parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-20 (LCK1) - Body ground Always 10 kΩ or higher
M35-15 (LCK2) - Body ground Always 10 kΩ or higher
M35-16 (REL2) - Body ground Always 10 kΩ or higher
M35-19 (REL1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE PARKING BRAKE ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR