Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A3  Open or Short Circuit in Lock Switch Circuit  C13AB  Lock Switch Circuit Comparison  


DESCRIPTION

When the electric parking brake switch (integration control and panel assembly) is pulled to the lock side, a lock request signal is output to the parking brake ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A3 Open or Short Circuit in Lock Switch Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pulled to lock side with power switch off.

2.

Terminal LCK1 voltage is less than 2.3 V or more than 4.35 V; or terminal LCK2 voltage is less than 1.4 V* or more than 9.0 V*.

3.

Problem occurs for approximately 1 second.


HINT:

*: This value is based on the assumption that the BECU terminal voltage is 11 V.

The threshold changes according to the BECU terminal voltage.

For details, refer to "Threshold Changes According to BECU Terminal Voltage".


·

Electric parking brake switch (integration control and panel assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.
C13AB Lock Switch Circuit Comparison Both of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (integration control and panel assembly) pulled to lock side with power switch off.

2.

ON/OFF judgment of lock switch 1 and lock switch 2 does not match for approximately 1 second.


·

Electric parking brake switch (integration control and panel assembly)

·

Wire harness or connector

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13A3 (Pattern 1, Pattern 2, Pattern 3, Pattern 4)
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ ○ - -
Power switch on (IG) - - ○ ○
Malfunction Status LCK1 terminal voltage is below 2.3 V ○ - ○ -
LCK1 terminal voltage is 4.35 V or more - ○ - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


DTC Detection Condition Combination Table: C13A3 (Pattern 5, Pattern 6, Pattern 7, Pattern 8)
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ ○ - -
Power switch on (IG) - - ○ ○
Malfunction Status LCK2 terminal voltage is below 1.4 V (*) ○ - ○ -
LCK2 terminal voltage is above 9.0 V (*) - ○ - ○
Detection Time Approximately 1 second Approximately 1 second Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip 1 trip 1 trip

HINT:
·

If the conditions match either of these patterns, a DTC will be output.

·

*: This value is based on the assumption that the BECU terminal voltage is 11 V.

The threshold changes according to the BECU terminal voltage.

For details, refer to "Threshold Changes According to BECU Terminal Voltage".



Threshold Changes According to BECU Terminal Voltage
C377928C04
0.427,0.542 0.74,0.74 0.313,0.198 10 false *c 0.427,0.813 0.74,1.01 0.313,0.198 10 false *d 0.656,1.729 0.969,1.927 0.313,0.198 10 false *b 2.219,3.177 2.531,3.375 0.313,0.198 10 false *a
*a BECU Terminal Voltage (V)
*b LCK2 Terminal Voltage (V)
*c Normal Range
*d DTC Detection Range


DTC Detection Condition Combination Table: C13AB
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Electric parking brake switch (integration control and panel assembly) is operated to lock side with power switch off ○ -
Power switch on (IG) - ○
Malfunction Status Lock 1 switch and lock 2 switch ON/OFF evaluations do not match ○ ○
Detection Time Approximately 1 second Approximately 1 second
Trip Count 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


WIRING DIAGRAM

C307302E16
4.917,0.521 5.531,0.719 0.615,0.198 10 false LCK1 4.927,1.104 5.542,1.302 0.615,0.198 10 false LCK2 4.656,0.396 4.969,0.594 0.313,0.198 10 false 20 4.656,0.99 4.969,1.188 0.313,0.198 10 false 15 4.938,2.281 5.552,2.479 0.615,0.198 10 false REL1 4.938,2.906 5.552,3.104 0.615,0.198 10 false REL2 4.635,2.156 4.948,2.354 0.313,0.198 10 false 19 4.635,2.813 4.948,3.01 0.313,0.198 10 false 16 2.885,0.385 3.5,0.583 0.615,0.198 10 false LCK1 2.875,0.969 3.49,1.167 0.615,0.198 10 false LCK2 3.333,0.969 3.646,1.167 0.313,0.198 10 false 21 3.375,0.375 3.688,0.573 0.313,0.198 10 false 10 2.896,2.167 3.51,2.365 0.615,0.198 10 false RLS1 2.885,2.802 3.5,3 0.615,0.198 10 false RLS2 3.365,2.156 3.677,2.354 0.313,0.198 10 false 22 3.365,2.771 3.677,2.969 0.313,0.198 10 false 23 0.906,3.938 1.521,4.135 0.615,0.198 10 false E 0.646,3.927 1.219,4.24 0.573,0.313 10 false 15 0.875,4.625 1.333,4.823 0.458,0.198 10 false G32 4.385,4.99 4.844,5.188 0.458,0.198 10 false M35 4.396,5.188 6.615,5.438 2.219,0.25 10 false Parking Brake ECU Assembly 1.635,1.625 3.365,2.042 1.729,0.417 10 false Lock Switch 1.667,3.458 3.49,4.104 1.823,0.646 10 false Release Switch 0.865,4.813 3.417,5.344 2.552,0.531 10 false Electric Parking Brake Switch (Integration Control and Panel Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When the electric parking brake switch (integration control and panel assembly) is pulled and held for 1 second or more without being pulled fully to the lock side, one of the 2 linked contacts may turn on while the other one turns off causing this DTC to be stored (system is not malfunctioning).

·

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)
a.

Remove the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL


b.

Inspect the electric parking brake switch (integration control and panel assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (INTEGRATION CONTROL AND PANEL ASSEMBLY))
a.

Disconnect the G32 electric parking brake switch (integration control and panel assembly) connector.


b.

Disconnect the M35 parking brake ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-20 (LCK1) - G32-10 (LCK1) Always Below 5 Ω
M35-15 (LCK2) - G32-21 (LCK2) Always Below 5 Ω
M35-20 (LCK1) or G32-10 (LCK1) - Body ground Always 10 kΩ or higher
M35-15 (LCK2) or G32-21 (LCK2) - Body ground Always 10 kΩ or higher
G32-15 (E) - Body ground Always Below 5 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Perform a lock operation with the electric parking brake switch (integration control and panel assembly).

HINT:

When the electric parking brake switch (integration control and panel assembly) is pulled and held for 1 second or more without being pulled fully to the lock side, one of the 2 linked contacts may turn on while the other one turns off causing this DTC to be stored (system is not malfunctioning).



e.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Proceed to
DTC is output
DTC is not output



DTC is output

REPLACE PARKING BRAKE ECU ASSEMBLY

DTC is not output