Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076413 PARKING BRAKE _0379234 ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(w/o Vacuum Brake Booster)  C13A9  Brake System Malfunction  


DESCRIPTION

The parking brake ECU assembly receives the wheel speed information of each wheel from the skid control ECU (brake booster with master cylinder assembly) via CAN communication.

This DTC is stored when a malfunction occurs in the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A9 Brake System Malfunction One of the following conditions is met:
1.

When the power switch is on (IG), all speed sensor malfunction signals input from the skid control ECU (brake booster with master cylinder assembly) continue for approximately 0.3 seconds or more.

2.

When the power switch is on (IG), brake system malfunction signal input from the skid control ECU (brake booster with master cylinder assembly) continues for approximately 0.3 seconds or more.

3.

When the parking brake is not operating while driving and the power switch is on (IG), an operating signal is input from the skid control ECU (brake booster with master cylinder assembly) for approximately 0.3 seconds or more when the parking brake ECU assembly is not outputting an operation request signal.


·

Skid control ECU (brake booster with master cylinder assembly)

·

Parking brake ECU assembly


Yes An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Condition Combination Table: C13A9
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ -
When the parking brake is not operating while driving and the power switch is on (IG) - - ○
Malfunction Status All speed sensor malfunction signals input from the skid control ECU (brake booster with master cylinder assembly) ○ - -
Brake system malfunction signal input from the skid control ECU (brake booster with master cylinder assembly) - ○ -
An operating signal is input from the skid control ECU (brake booster with master cylinder assembly) when the parking brake ECU assembly is not outputting an operation request signal - - ○
Detection Time Approximately 0.3 seconds Approximately 0.3 seconds Approximately 0.3 seconds
Trip Count 1 trip 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the parking brake ECU assembly, operate the electric parking brake switch (integration control and panel assembly) from the lock side to the release side, as the parking brake indicator light blinks when the power switch is first turned on (IG).


PROCEDURE

1.CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster))
a.

Check for DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

2.CHECK DTC (ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster))

DTC is output

2.CHECK DTC (ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster))
a.

Clear the DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Clear DTCs
50002 184

b.

Turn the power switch off.


c.

Check for DTC.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Proceed to
DTC is output
DTC is not output



DTC is output

REPLACE PARKING BRAKE ECU ASSEMBLY

DTC is not output