Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  FREEZE FRAME DATA  


FREEZE FRAME DATA/INFORMATION


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.


b.

The freeze frame data that is recorded when a DTC is stored can be used to check the INF codes, but only for DTCs which can be stored.



CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES


a.

Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.


b.

Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the power switch has been turned from off to on (IG) since the last time the system was activated can be stored and displayed.

HINT:
·

When the vehicle is stopped (vehicle speed below 7 km/h), turning the power switch from off to on (IG) does not cause the value to increase.

·

The value "31" is displayed when the power switch was turned on (IG) more than 31 times.




d.

Check freeze frame data when the system operates

i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3 and turn the power switch on (IG).


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility.


iv.

Select "ABS History".

Chassis > ABS/VSC/TRC > Utility
Tester Display
ABS History
50005 105 1008

v.

Check the freeze frame data when the system operates.




CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED


a.

Freeze frame data is stored when a DTC is output.


b.

Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the power switch has been turned from off to on (IG) since a DTC was output can be stored and displayed.

HINT:

The value "31" is displayed when the power switch was turned on (IG) more than 31 times.



d.

Check the freeze frame data and INF code when a DTC is output.

i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3 and turn the power switch on (IG).


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

iv.

Select a DTC to display the freeze frame data.


v.

Check the freeze frame data for the output DTC.

HINT:

If an "INF Code" item appears when the freeze frame data is displayed, select and check the INF code.


Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Detailed Freeze DTC Detailed code for Freeze Frame DTC Min.: 0, Max.: 65535 - Number of information codes (INF code) output is displayed
Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 msec, Max.: 510 msec - -
Number of IG ON Number of times power switch turned on (IG) after Freeze Frame Data stored 0 to 31 - -
Elapsed Time Elapsed time after power switch turned on (IG) Min.: 0 sec, Max.: 100661 sec - -
Buzzer Meter buzzer ON or OFF ON: Buzzer on
OFF: Buzzer off
-
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Reservoir Warning SW Brake fluid level warning switch ON or OFF ON: Reservoir level low
OFF: Reservoir level normal
-
Shift Lever Position Shift position information Fail, 1st-6th/B, D/M, P,N or R Actual shift position -
Operated System Operated system status Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC, SCB or Sys - Non: No system activated
ABS: ABS activated
VSC: VSC activated
TRC: TRC (TRAC) activated
BA: BA activated
HAB: High power assist brake activated*1
Fail: Fail safe mode activated
PBA: PBA activated*2
PB: PB activated*2
HA-CTRL: Hill-start assist control activated
TSC: Trailer sway control activated
SCB: Secondary collision brake
Sys: System prohibited
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Yaw Rate Sensor Yaw rate sensor Min.: -128 °/s, Max.: 127 °/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 127.5% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
ECB Motor Relay ABS motor relay ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Main Relay ABS main relay ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
IG1 Voltage Value IG1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
IG2 Voltage Value IG2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
BS1 Voltage Value BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
VM1 Voltage Value VM1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
Motor Relay Voltage Value Motor relay voltage value Min.: 0.00 V, Max.: 20.00 V During motor operation: 12.00 V
No motor operation: 0.00 V
-
Steering Angle Sensor Steering sensor Min.: - 3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
TRC/VSC Off Mode TRC (TRAC)/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC (TRAC) off mode
VSC OFF: VSC off mode
-
Brake Hold Control Brake hold control status OFF, Hold, Release or EPB OFF: Brake hold control not operating
Hold: Brake hold operating during brake hold control
Release: Brake hold released during brake hold control
EPB: Electric parking brake operating during brake hold control
EPB: Electric Parking Brake System
Regulator Pressure Sensor Output Regulator pressure sensor output Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
Regulator Pressure Sensor Output Variant Regulator pressure sensor output variant Min.: -30 MPa/s, Max.: 225 MPa/s - -
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed
SLA Solenoid Current Linear solenoid additional valve (SLA) current Min.: 0.00 A, Max.: 1.50 A Brake pedal released: 0.00 A -
SLR Solenoid Current Linear solenoid reduction valve (SLR) current Min.: 0.00 A, Max.: 1.50 A Brake pedal released: 0.00 A -
Target Oil Pressure Wheel target hydraulic pressure Min.: 0.00 Mpa, Max.: 20.00 Mpa - Changes according to the target wheel cylinder hydraulic pressure
ECB Solenoid (SSC) Simulator cut solenoid valve (SSC) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
ECB Solenoid (SCC) Switching solenoid valve (SCC) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
ECB Solenoid (SMC) Master cut solenoid valve (SMC) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
ECB Solenoid (SRC) Regulator cut solenoid valve (SRC) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
Voltage of Stroke Sensor Voltage of brake pedal stroke sensor assembly Min.: -2.50 V, Max.: 2.49 V - -
Voltage of Stroke Sensor2 Voltage of brake pedal stroke sensor assembly 2 Min.: -2.50 V, Max.: 2.49 V - -

*1: Not supported

*2: w/ Pre-collision System





CLEAR FREEZE FRAME DATA AND INFORMATION


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data and information codes (INF codes).


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105