Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  Abnormal Brake Pedal Response on First Depression  


DESCRIPTION

If the vehicle has been stopped without opening or closing the driver door for a long period of time, the electronically controlled brake system will not be ready and sufficient fluid pressure may not be stored in the accumulator. In this case, the brake pedal response may not be the same as usual the first time the brake pedal is depressed. This is not a malfunction.

WIRING DIAGRAM

C407570E03
5.094,1.969 5.406,2.167 0.313,0.198 10 false 19 5.427,1.969 5.813,2.188 0.385,0.219 10 false CTY 0.573,1.146 2.406,1.552 1.833,0.406 10 false to Main Body ECU (Multiplex Network Body ECU) 3.573,2.042 3.885,2.24 0.313,0.198 10 false 1 1.75,2.5 2.604,2.76 0.854,0.26 10 false N7*1, M4*2 1.76,2.688 4.729,2.958 2.969,0.271 10 false Front Door Courtesy Light Switch Assembly 5.073,3.906 5.385,4.104 0.313,0.198 10 false A42 5.063,4.094 7.125,4.51 2.063,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.146,3.958 2.01,4.24 0.865,0.281 10 false *1: for LHD 1.167,4.323 2.031,4.604 0.865,0.281 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check the conditions at the time the problem occurred.

i.

Whether a warning light illuminated or the buzzer sounded.


ii.

The number of times the power switch was turned on (IG) since the latest symptom occurred.


iii.

Frequency of the symptom.



Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE
2.CHECK VEHICLE
a.

Turn the power switch off.


b.

Depress the brake pedal within 2 minutes of opening the driver door and check the response of the brake pedal.


c.

Release the brake pedal and wait for 2 minutes without depressing the brake pedal, opening or closing the driver door or operating the power switch.


d.

After 2 seconds or more have elapsed, depress the brake pedal and check that the first depression response is different to successive depression responses.

HINT:

Compare the response of the brake pedal when the system is in sleep mode and when the stroke simulator is operating.



Result:
Result Proceed to
The response of the brake pedal does not change. A
The response of the brake pedal changed. B



A

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

B

END

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Set the interior light door switch to ON and check that the map light assembly illuminates, then set the interior light door switch to DOOR.


b.

Check that the map light assembly illuminates when the driver door is opened.

OK:

The map light assembly illuminates when the driver door is opened.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

INSPECT LIGHTING SYSTEM (COURTESY LIGHT SWITCH CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.
C405855C08
0.208,0.802 0.625,1.073 0.417,0.271 1.656,1.885 2.219,2.729 2.219,2.729 2.469,2.729 true 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.281,0.854 0.969,1.167 0.688,0.313 10 false A42 2.542,2.656 2.948,2.865 0.406,0.208 10 false CTY
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-19 (CTY) - Body ground Driver door open 1.5 V or less
A42-19 (CTY) - Body ground Driver door closed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT)