Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD without Vacuum Brake Booster) › 2018.10–2020.08
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377040 BRAKE BOOSTER(for RHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD without Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of skid control ECU (brake booster with master cylinder assembly)
·

Clear the zero point calibration data and stored linear solenoid valve calibration data

·

Perform initialization and calibration of the linear solenoid valve

·

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2. DISABLE BRAKE CONTROL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:

Use the same procedure as for LHD.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


Hide 55704B 4.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 87211A 7.REMOVE NO. 2 AIR DUCT

Hide 84340 8.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 10.SEPARATE WIRE HARNESS

a.
C409064

Disconnect the connector from the brake pedal stroke sensor assembly.


b.

Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.


Hide 12.REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH RESERVOIR HOSE

a.
C407872

Slide the 3 clips and disconnect the 3 hoses.


b.
C407873

Remove the 2 nuts and remove the brake master cylinder reservoir with reservoir hose from the reservoir bracket.


Hide 47233 13.REMOVE RESERVOIR BRACKET

a.
C407874

Remove the bolt, 2 nuts and reservoir bracket.


Hide 47210L 14.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C407875C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Disengage the clamp.


b.

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

NOTICE:

Be careful not to allow the brake fluid to enter the removed connector.



c.
C407876C01
1.167,0.708 0.917,0.375 0.917,0.375 0.75,0.375 true 1.229,1.365 1.125,1.917 1.125,1.917 0.833,1.917 true 1.24,1.167 1.677,1.406 1.677,1.406 1.865,1.406 true 2.146,0.729 2.313,0.146 2.313,0.146 2.531,0.146 true 1.177,0.969 0.865,0.74 0.865,0.74 0.698,0.74 true 0.531,0.271 0.771,0.49 0.24,0.219 10 true *a 0.531,0.656 0.75,0.854 0.219,0.198 10 true *b 1.938,1.333 2.167,1.531 0.229,0.198 10 true *c 0.667,1.844 0.896,2.052 0.229,0.208 10 true *d 2.594,0.063 2.875,0.24 0.281,0.177 10 true *e
*a To Front Wheel Cylinder LH
*b To Rear Wheel Cylinder RH
*c To Brake Booster Pump Assembly
*d To Rear Wheel Cylinder LH
*e To Front Wheel Cylinder RH


Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


d.
C407883

Disengage the 4 clamps to remove the brake tube clamp from the brake lines.


e.
C407884

Disengage the 4 clamps to separate the brake tube clamp from the brake lines.


f.

Disengage the clamp and remove the brake tube clamp from the brake booster with master cylinder assembly.


g.
C407885

Disengage the 4 clamps to separate the brake tube clamp from the brake lines.


h.

Disengage the clamp and remove the brake tube clamp from the vehicle body.


i.
C407877

Disengage the clamp to separate the front No. 3 brake tube from the brake tube clamp.


j.
C407878

Using a union nut wrench, disconnect the front No. 3 brake tube from the front flexible hose RH.


k.
C407879

Disengage the grommet and separate the front No. 3 brake tube.


l.
C407880

Disengage the clamp and remove the brake tube clamp from the brake tube clamp bracket.


m.
C407881

Remove the bolt and separate the brake tube clamp bracket.


n.
C407882

Disengage the clamp to separate the suction pipe sub-assembly.


o.
C407886C01
1.719,2.646 2.219,2.646 false 1.438,3.833 0.75,4.125 0.75,4.125 1.385,4.125 true 1.719,3.063 0.583,2.583 0.583,2.583 1.313,3.094 true 2.74,3.469 2.917,3.677 2.917,3.677 3.083,3.677 false 2.406,3.583 2.698,3.938 2.698,3.938 2.865,3.938 false 2.281,2.583 2.594,2.74 0.313,0.156 10 false *1 0.396,2.469 0.708,2.625 0.313,0.156 10 false *2 3.146,3.615 3.427,3.823 0.281,0.208 10 false *3 2.917,3.854 3.229,4.01 0.313,0.156 10 false *4 0.563,4.042 0.875,4.198 0.313,0.156 10 false *5
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.




Hide 44785C 15.REMOVE BRAKE BOOSTER GASKET