While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.
If the TCM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores this DTC.
This monitor begins running when the vehicle is driven at 20 km/h (12 mph) or more for 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P061512 | Starter Relay Circuit Short to Battery | All of the following conditions are met (1-trip detection logic):
·
The battery voltage is 10.5 V or more. ·
The vehicle speed is 20 km/h (12 mph) or more. ·
The engine speed is more than 1000 rpm. ·
The starter signal is ON for 20 seconds or more. |
·
ST NO. 1 relay ·
Starter signal circuit ·
Park/neutral position switch assembly ·
ECM ·
TCM ·
Engine stop and start ECU (w/ Stop and Start System) ·
Certification ECU (Smart key ECU assembly) (w/ Entry and Start System) |
Comes on | DTC stored | SAE Code:
P0617 |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Drive the vehicle for 20 seconds or more with the following conditions met:
Engine speed is 1000 rpm or more.
Vehicle speed is 20 km/h (12 mph) or more.
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P061512.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Strictly observe posted speed, limits, traffic laws and road conditions.
Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.
Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.
Do not operate the GTS while driving the vehicle.
Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Confirm the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
According to the display on the GTS, read the Data List.
| Switch Condition | Starter SW |
|---|---|
| Ignition switch ON | OFF |
According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.
| Condition | Starter SW |
|---|---|
| Driving at 20 km/h (12 mph) or more (engine speed 1000 rpm or more) | OFF |
If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, the GTS connected and Data List item "Starter SW" selected.
| Proceed to |
|---|
| OK |
| NG |
If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
According to the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| The Data List item "Starter SW" does not change from ON. | A |
| The Data List item "Starter SW" changes from ON to OFF. | B |
When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
The purpose of this step is to check for ST NO. 1 relay terminal voltage under abnormal conditions.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Measure the voltage between ST NO. 1 relay terminal 2 and body ground.
Make a note of the measured voltage as it will be necessary for inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 1 relay.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:
Short to +B in the circuit of a connected ECU or the switch.
Short to +B in the wire harness.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the C31 park/neutral position switch assembly connector.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Disconnect the A34 engine stop and start ECU connector.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the engine stop and start ECU is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Disconnect the C33 TCM connector.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) | B |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | C |
If the voltage is the same before and after disconnecting the connector, the TCM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
C
Disconnect the C33 TCM connector.
Disconnect the C31 park/neutral position switch assembly connector.
Disconnect the A15 certification ECU (smart key ECU assembly) connector.
Disconnect the A34 engine stop and start ECU connector.
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-28 (STA), C31-5 (L), A15-20 (STA), A34-21 (STA) or 2 (ST NO. 1 relay) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
According to the display on the GTS, read the Data List.
| Switch Condition | Starter SW |
|---|---|
| Ignition switch ON | OFF |
According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.
| Condition | Starter SW |
|---|---|
| Driving at 20 km/h (12 mph) or more (engine speed 1000 rpm or more) | OFF |
If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, the GTS connected and Data List item "Starter SW" selected.
| Proceed to |
|---|
| OK |
| NG |
If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
According to the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| The Data List item "Starter SW" does not change from ON. | A |
| The Data List item "Starter SW" changes from ON to OFF. | B |
When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
The purpose of this step is to check for ST NO. 1 relay terminal voltage under abnormal conditions.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Measure the voltage between ST NO. 1 relay terminal 2 and body ground.
Make a note of the measured voltage as it will be necessary for inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST NO. 1 relay.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:
Short to +B in the circuit of a connected ECU or the switch.
Short to +B in the wire harness.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the C31 park/neutral position switch assembly connector.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Disconnect the C33 TCM connector.
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the ECM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Disconnect the A24 ECM connector.
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Measure the voltage between ST NO. 1 relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/ Entry and Start System) | A |
| The voltage between ST NO. 1 relay terminal 2 and body ground does not change when the connector is disconnected. (w/o Entry and Start System) | B |
| The voltage between ST NO. 1 relay terminal 2 and body ground changes when the connector is disconnected. | C |
If the voltage is the same before and after disconnecting the connector, the ECM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
C
Disconnect the A24 ECM connector.
Disconnect the C31 park/neutral position switch assembly connector.
Disconnect the A15 certification ECU (smart key ECU assembly) connector.
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-30 (STA), C31-5 (L), A15-20 (STA), C33-28 (STA) or 2 (ST NO. 1 relay) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION