Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071011  Transmission Fluid Temperature Sensor "A" Circuit Short To Ground  


DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the TCM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The TCM applies voltage to the temperature sensor through TCM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground When the battery voltage is 8 V or more and the ignition switch is ON, the CVT fluid temperature sensor voltage is less than 0.142 V for 0.5 seconds (1-trip detection logic).
·

Wire harness or connector

·

Transmission wire (CVT fluid temperature sensor)

·

TCM


Comes on DTC stored SAE Code:
P0712

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the TCM determines the CVT fluid temperature and can detect a short to ground in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*, the TCM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.

*: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked in the Data List.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 3 seconds or more with the ignition switch ON.

7.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

8.

Input the DTC: P071011.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C318996E44
1.49,1.74 3.458,1.927 1.969,0.188 10 false CVT Fluid Temperature Sensor 1.594,2.729 3.427,2.927 1.833,0.198 10 false Transmission Wire 0.76,3.156 3.552,3.354 2.792,0.198 10 false Continuously Variable Transaxle Assembly 6.052,3.323 6.969,3.667 0.917,0.344 10 false TCM 3.531,1.125 3.99,1.323 0.458,0.198 10 false OT+ 3.552,2.104 4.01,2.302 0.458,0.198 10 false OT- 3.917,2.104 4.375,2.302 0.458,0.198 10 false 12 3.917,1.135 4.375,1.333 0.458,0.198 10 false 11 5.323,1.125 5.781,1.323 0.458,0.198 10 false 51 5.594,1.125 6.052,1.323 0.458,0.198 10 false THO1 5.604,2.104 6.063,2.302 0.458,0.198 10 false ETHO 5.333,2.104 5.792,2.302 0.458,0.198 10 false 52 6.281,0.979 6.74,1.177 0.458,0.198 10 false 5 V 1.594,2.563 2.031,2.771 0.438,0.208 10 false C34 6.052,3.156 6.625,3.427 0.573,0.271 10 false C33

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Data List.


f.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 100°C (212°F): After stall speed test

·

Equal to ambient temperature: After cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

2.REPLACE TCM

B

3.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
2.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

3.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C397724C02
2.083,1.552 0.979,1.333 true 2.25,1.563 2.865,1.344 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.917,1.26 3.302,1.458 0.385,0.198 10 false OT+ 0.688,1.24 1.302,1.438 0.615,0.198 10 false OT-
*a Component without harness connected
(Transmission Wire)


Disconnect the C34 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (OT+) - 12 (OT-) Always 79 Ω to 156 kΩ
11 (OT+) - Body ground and other terminals Always 10 kΩ or higher
12 (OT-) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5.6 to 7.3 kΩ
25°C (77°F) 3.5 kΩ
110°C (230°F) 0.22 to 0.27 kΩ



c.

Connect the C34 transmission wire connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

REPLACE TRANSMISSION WIRE

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C33 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-51 (THO1) - C33-52 (ETHO) Always 79 Ω to 156 kΩ
C33-51 (THO1) - Body ground and other terminals Always 10 kΩ or higher
C33-52 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the C33 TCM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM)

5.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT