Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The TCM uses signals from the transmission revolution sensor (NT) installed to the continuously variable transaxle to control the lock-up engagement pressure.

The transmission revolution sensor (NT) detects the input turbine speed and sends it to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery The transmission revolution sensor (NT) signal is normal but the transmission revolution sensor (NT) output voltage is higher than 1.8 V for 2 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE Code:
P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open The transmission revolution sensor (NT) signal is normal but the transmission revolution sensor (NT) output voltage is less than 0.2 V for 2 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE Code:
P07BF
P071531 Input/Turbine Speed Sensor "A" No Signal When transmission revolution sensor (NSS) and (NOUT) signals both indicate 780 rpm or more, the transmission revolution sensor (NT) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic).
·

Wire harness or connector

·

Transmission revolution sensor (NT)

·

TCM


Comes on DTC stored SAE Code:
P0717

MONITOR DESCRIPTION

The transmission revolution sensor (NT) is used to detect the input turbine speed. The TCM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input turbine speed) and transmission revolution sensor (NOUT) (output shaft speed) signals.

When the output shaft speed is higher than the expected value and the input turbine speed is less than 300 rpm while driving with the shift lever in D, the TCM will determine that the transmission revolution sensor (NT) is malfunctioning, illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P071512, P071514 or P071531.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C318994E37
0.323,2.844 3.844,3.042 3.521,0.198 10 false Transmission Revolution Sensor (NT) 5.979,3.042 6.5,3.333 0.521,0.292 10 false TCM 5.688,1.125 6.406,1.479 0.719,0.354 10 false NTB 5.396,1.125 5.854,1.323 0.458,0.198 10 false 25 2.104,1.125 2.563,1.323 0.458,0.198 10 false 2 1.667,1.125 2.229,1.365 0.563,0.24 10 false NTB 1.677,2.094 2.219,2.323 0.542,0.229 10 false NTO 2.104,2.094 2.563,2.292 0.458,0.198 10 false 1 5.458,2.094 5.917,2.292 0.458,0.198 10 false 9 5.677,2.094 6.135,2.292 0.458,0.198 10 false NTO 5.979,2.896 6.438,3.094 0.458,0.198 10 false C33 0.323,2.677 0.781,2.875 0.458,0.198 10 false C35 6.302,0.958 6.76,1.156 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed, limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input turbine speed (NT) Min.: 0 rpm
Max.: 65535 rpm
·

Equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


-
NT Sensor Voltage Transmission revolution sensor (NT) output voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

2.REPLACE TCM

B

3.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
2.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT

3.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.

Remove the transmission revolution sensor (NT).

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>REVOLUTION SENSOR (NT SENSOR)>REMOVAL


b.

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.

C397726C01
1.448,1.833 1.615,1.417 true 2.083,1.833 1.917,1.417 true 4.083,1.104 4.333,1.354 true 4.625,1.354 4.875,1.604 true 5.854,0.917 6.167,1.073 0.313,0.156 10 false *1 5.125,0.573 5.438,0.729 0.313,0.156 10 false *2 1.208,0.656 1.521,0.813 0.313,0.156 10 false *a 4.646,1.823 4.958,1.979 0.313,0.156 10 false *b 3.781,2.229 4.094,2.385 0.313,0.156 10 false *c 1.313,1.854 1.771,2.052 0.458,0.198 10 false NTB 1.969,1.854 2.427,2.052 0.458,0.198 10 false NTO 3.969,1.021 4.125,1.219 0.156,0.198 10 false 2 4.917,1.552 5.073,1.75 0.156,0.198 10 false 1
*1 Battery *2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm or less - -



c.

Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
1 (NTO) - 2 (NTB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)
a.

Disconnect the C35 transmission revolution sensor (NT) connector.


b.

Disconnect the C33 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C35-2 (NTB) - C33-25 (NTB) Always Below 1 Ω
C35-1 (NTO) - C33-9 (NTO) Always Below 1 Ω
C35-2 (NTB) or C33-25 (NTB) - Body ground and other terminals Always 10 kΩ or higher
C35-1 (NTO) or C33-9 (NTO) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C33 TCM connector.


e.

Connect the C35 transmission revolution sensor (NT) connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)

5.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT