The TCM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P084011 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Short To Ground | When 2 seconds or more have elapsed since engine start, a short to ground is detected in the oil pressure sensor circuit for 0.5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Oil pressure sensor ·
TCM |
Comes on | DTC stored | SAE Code:
P0842 |
This DTC indicates a short to ground in the oil pressure sensor circuit. If there is a short to ground in the oil pressure sensor circuit, the TCM detects the malfunction, illuminates the MIL and stores a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and wait for 5 seconds or more.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P084011.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chocks are out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Perform this test with the AUTO function (shift-linked function) of the electric parking brake system off.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (integration control and panel assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (integration control and panel assembly) is pulled to the lock side one more time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the TC Terminal | Turn on and off TC and TE1 (CG) connection | ON or OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. (Vehicle Condition)
Ignition switch ON, engine stopped and shift lever in P |
Enter the following menus: Powertrain / Transmission / Data List / Belt Clamping Force Sensor.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm2, 508 to 624 psi): D position stall test ·
1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm2, 232 to 348 psi): R position stall test |
- |
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C38-3 (VC) - C38-1 (E2) | Ignition switch ON | 4.75 to 5.25 V |
Connect the oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C38 oil pressure sensor connector.
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-2 (PTO) - C33-50 (PTO) | Always | Below 1 Ω |
| C38-2 (PTO) or C33-50 (PTO) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
Connect the C38 oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform Initialization.
Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and wait for 5 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P084011 is output | B |
A
B
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the C38 oil pressure sensor connector.
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-3 (VC) - C33-49 (VCPT) | Always | Below 1 Ω |
| C38-1 (E2) - C33-48 (EPTO) | Always | Below 1 Ω |
| C38-3 (VC) or C33-49 (VCPT) - Body ground and other terminals | Always | 10 kΩ or higher |
| C38-1 (E2) or C33-48 (EPTO) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
Connect the C38 oil pressure sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION