Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0374959 AUTOMATIC TRANSAXLE SYSTEM C

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P27137F  Pressure Control Solenoid "D" Actuator Stuck Off  


DESCRIPTION

Based on signals from the accelerator position sensor and transmission revolution sensors (NT and NC), the ECM controls the solenoid (SLT) valve using a predetermined current. As a result, the line pressure is adjusted to a pressure that is appropriate for the throttle angle and engine output. Based on the rotation speed signals from the transmission revolution sensors (NT and NC), the ECM calculates the heat level of the friction material, and detects clutch slippage, etc.

C361129C01
4.823,1.656 4.167,0.75 4.167,0.75 4,0.75 true 4.594,1.948 4.167,2.5 4.167,2.5 4,2.5 true 6.083,1.5 5.167,2.865 5.167,2.865 6.083,2 true 1.615,2.792 2.688,2.99 1.073,0.198 10 false *a 0.75,2.021 1.385,2.427 0.635,0.406 10 false *b 3.802,0.667 5.49,0.865 1.688,0.198 10 false *1 3.813,2.417 4.729,2.615 0.917,0.198 10 false *2 5,2.802 6.99,3 1.99,0.198 10 false *3
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Current *b Hydraulic Pressure


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P27137F Pressure Control Solenoid "D" Actuator Stuck Off All of the following conditions are met (2-trip detection logic):
·

Engine coolant temperature is 40°C (104°F) or higher.

·

ATF temperature is -10°C (14°F) or higher.

·

The vehicle is being driven with the shift lever in D.

·

No malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuits, electronic throttle or CAN communication system.

·

The transmission revolution sensor (NT) value exceeds the specified speed for each gear for 0.5 seconds or more.


·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SL) valve

·

Solenoid (SLU) valve

·

Solenoid (SLT) valve

·

Transmission valve body assembly

·

Automatic transaxle assembly (clutch, brake, gear, etc.)


Comes on DTC stored SAE Code:
P2714

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the clutch discs and brake discs based on the difference in speed (clutch slippage) between the turbine (input) and output shaft. If the amount of heat absorption exceeds the specified value, the ECM will illuminate the MIL and store this DTC.

If the solenoid (SLT) valve is stuck ON, the line pressure and clutch engagement force will decrease.

NOTICE:

If driving continues under these conditions, the clutches will burn out and the vehicle will no longer be drivable.


CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P27137F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P27137F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTC P27137F and DTC P07457F, P07407E, P07757F, P07957F, P08BA7F, P28077F and/or P28167F are output A
Only DTC P27137F is output B
DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are output C


HINT:
·

If any DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.

·

If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.





A

2.CLEAR DTC AND PERFORM STALL SPEED TEST

B

5.INSPECT SOLENOID (SLT) VALVE

C

2.CLEAR DTC AND PERFORM STALL SPEED TEST
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373
HINT:

Write down the currently output DTCs before clearing them.



b.

Perform the stall speed test.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>MECHANICAL SYSTEM TESTS

Result:
Test Condition Proceed to
Stall speed test can be performed A
Stall speed test cannot be performed B




A

3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE

B

5.INSPECT SOLENOID (SLT) VALVE
3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) Valves)


Remove the solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) valves.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL1) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL2) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL3) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL4) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL5) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL6) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL) VALVE

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) OR (SL6) VALVE

4.INSPECT SOLENOID (SL) VALVE
a.
C361133C03
0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 2.583,0.24 3.042,0.438 0.458,0.198 10 false (+) 1.594,0.26 2.052,0.458 0.458,0.198 10 false (-)
*1 Solenoid (SL) Valve


Remove the solenoid (SL) valve.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

5.INSPECT SOLENOID (SLT) VALVE

NG

5.INSPECT SOLENOID (SLT) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLT) Valve)


Remove the solenoid (SLT) valve.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLT) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Inspect the transmission valve body assembly.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.



Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

7.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY
a.

Repair or replace the automatic transaxle assembly.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT