Home › Drivetrain › UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076123 UB80F AUTOMATIC TRANSMISSION / TRANSAXLE _0374959 AUTOMATIC TRANSAXLE SYSTEM C

UB80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P275614  Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P275612.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P275612

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P275614 Torque Converter Clutch Pressure Control Solenoid Control Circuit Short to Ground or Open While the vehicle is being driven, a short to ground or open is detected in the solenoid (SLU) valve circuit for 1 second or more (1-trip detection logic).
·

Solenoid (SLU) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P2764

MONITOR DESCRIPTION

When an open or short to ground in the solenoid (SLU) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the Lock-up Function inspection in Road Test.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P275614.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLU) VALVE) - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-12 (SLU+) - C41-11 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C41-12 (SLU+) or C41-11 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-5 (SLU+) - C41-12 (SLU+) Always Below 1 Ω
C30-4 (SLU-) - C41-11 (SLU-) Always Below 1 Ω
C30-5 (SLU+) or C41-12 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C30-4 (SLU-) or C41-11 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SLU) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.INSPECT SOLENOID (SLU) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLU) Valve)


Remove the solenoid (SLU) valve.

Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLU) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes operating sound.



Result:
Proceed to
OK
NG



OK

NG