Moving the shift lever to S enables the shift range to be selected. The shift range can be selected by operating the "+" or "-" shift paddle switch.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sport Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" or "+" shift paddle switch operated ·
OFF: Shift lever not held in "+" and "+" shift paddle switch released |
- |
| Sport Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" or "-" shift paddle switch operated ·
OFF: Shift lever not held in "-" and "-" shift paddle switch released |
- |
| Tester Display |
|---|
| Sport Shift Up SW |
| Sport Shift Down SW |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-20 (SFTU) - A24-28 (ECCS) | "+" (Up shift) shift paddle switch operated and held | Below 2.5 Ω |
| "+" (Up shift) shift paddle switch not operated | 1 MΩ or higher | |
| A24-19 (SFTD) - A24-28 (ECCS) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-10 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the spiral cable sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-20 (SFTU) - G20-8 (SUP) | Always | Below 1 Ω |
| A24-19 (SFTD) - G20-1 (SDN) | Always | Below 1 Ω |
| A24-28 (ECCS) - G20-2 (ECC) | Always | Below 1 Ω |
| A24-20 (SFTU) or G20-8 (SUP) - Body ground | Always | 10 kΩ or higher |
| A24-19 (SFTD) or G20-1 (SDN) - Body ground | Always | 10 kΩ or higher |
| A24-28 (ECCS) or G20-2 (ECC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Paddle Switch LH (No. 1 Transmission Shift Switch Assembly)) |
Remove the shift paddle switch LH (No. 1 transmission shift switch assembly).
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SDN) - A-2 (ECC) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher | |
| A-1 (SDN) - A-3 (ECC') | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Paddle Switch RH (No. 2 Transmission Shift Switch Assembly)) |
Remove the shift paddle switch RH (No. 2 transmission shift switch assembly).
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SUP) - B-2 (ECC') | "+" (Up shift) shift paddle switch operated and held | Below 2.5 Ω |
| "+" (Up shift) shift paddle switch not operated | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Install the transmission shift switch assembly.
Click hereDrivetrain>UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>INSTALLATION
Disconnect the No. 1 switch wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z5-2 (SUP) - z5-3 (ECC) | "+" (Up shift) shift paddle switch operated and held | Below 2.5 Ω |
| "+" (Up shift) shift paddle switch not operated | 1 MΩ or higher | |
| z5-4 (SDN) - z5-3 (ECC) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG