Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Air Conditioning Amplifier" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Air conditioning amplifier assembly branch wire or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C405880E03
0.292,1.927 2.26,2.219 1.969,0.292 10 false No. 1 CAN Junction Connector 0.292,1.75 0.76,2.01 0.469,0.26 10 false G96 1.708,1.458 2.042,1.719 0.333,0.26 10 false 16 1.74,0.885 2.073,1.146 0.333,0.26 10 false 5 5.354,0.896 5.688,1.156 0.333,0.26 10 false 2 5.354,1.458 5.688,1.719 0.333,0.26 10 false 1 3.99,2.344 5.083,2.656 1.094,0.313 10 false ECU-B NO.2 5.375,2.365 5.708,2.625 0.333,0.26 10 false 5 5.375,3.188 5.708,3.448 0.333,0.26 10 false 6 1.76,2.448 3.24,2.719 1.479,0.271 10 false from Auxiliary Battery 1.75,3.271 3.365,3.615 1.615,0.344 10 false from IG1 NO.1 Relay 5.365,4.01 5.698,4.271 0.333,0.26 10 false 17 5.656,4.146 5.99,4.406 0.333,0.26 10 false GND 5.667,3.313 6,3.573 0.333,0.26 10 false IG+ 5.667,2.5 6,2.76 0.333,0.26 10 false B 5.656,1.01 6.281,1.26 0.625,0.25 10 false CANH 5.667,1.594 6.344,1.906 0.677,0.313 10 false CANL 5.313,4.719 5.646,4.979 0.333,0.26 10 false G46 5.344,4.885 6.885,5.313 1.542,0.427 10 false Air Conditioning Amplifier Assembly 4,3.167 5.094,3.479 1.094,0.313 10 false ECU-IG1 NO.4

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
B532755C01
1.583,0.333 2.01,0.604 0.427,0.271 1.115,1.135 0.802,0.594 0.802,0.594 0.615,0.594 true 1.25,1.188 0.729,1.896 0.729,1.896 0.542,1.896 true 1.667,0.385 2.125,0.583 0.458,0.198 10 false G46 0.24,0.521 0.698,0.719 0.458,0.198 10 false CANL 0.135,1.813 0.594,2.01 0.458,0.198 10 false CANH 0.135,0.073 0.594,0.271 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-2 (CANH) - G46-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
B532755C02
1.594,0.26 2.01,0.552 0.417,0.292 0.635,1.885 0.844,1.885 0.844,1.885 1.167,1.354 true 2.948,2 2.719,2 2.719,2 2.531,1.344 true 0.573,0.719 0.781,0.719 0.781,0.719 1.073,1.292 true 1.667,0.323 2.125,0.521 0.458,0.198 10 false G46 3,1.948 3.375,2.146 0.375,0.198 10 false GND 0.406,0.635 0.781,0.833 0.375,0.198 10 false B 0.354,1.792 0.729,1.99 0.375,0.198 10 false IG+ 0.135,0.115 0.51,0.313 0.375,0.198 10 false *a
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-17 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G46-5 (B) - Body ground Power switch off 11 to 14 V
G46-6 (IG+) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR