Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Combination Meter" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Combination Meter" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Combination meter assembly main wire or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C409783E02
5.656,0.896 6.135,1.052 0.479,0.156 10 false CANH 5.677,1.677 6.156,1.833 0.479,0.156 10 false CANL 5.698,3.156 6.177,3.313 0.479,0.156 10 false B 5.677,2.396 6.156,2.552 0.479,0.156 10 false IG+ 5.677,3.885 6.135,4.115 0.458,0.229 10 false EP 5.417,0.875 5.74,1.073 0.323,0.198 10 false 9 5.354,1.406 5.635,1.604 0.281,0.198 10 false 25 5.354,2.25 5.667,2.438 0.313,0.188 10 false 38 5.354,3.01 5.635,3.208 0.281,0.198 10 false 22 5.365,4.167 5.771,4.365 0.406,0.198 10 false 23 1.573,0.896 1.729,1.094 0.156,0.198 10 false 2 1.552,1.417 1.833,1.615 0.281,0.198 10 false 8 0.25,1.885 0.76,2.177 0.51,0.292 10 false N52 0.25,2.042 2.385,2.354 2.135,0.313 10 false No. 7 CAN Junction Connector 3.896,2.969 4.938,3.375 1.042,0.406 10 false ECU-DCC NO.2 4.031,2.198 4.938,2.375 0.906,0.177 10 false METER-IG2 1.75,3.052 3.344,3.365 1.594,0.313 10 false from Auxiliary Battery 1.781,2.313 3.219,2.635 1.438,0.323 10 false from IG2 NO.2 Relay 5.24,4.792 5.823,5.073 0.583,0.281 10 false G18 5.229,4.958 7.063,5.229 1.833,0.271 10 false Combination Meter Assembly 5.365,3.771 5.771,3.969 0.406,0.198 10 false 19 5.677,4.302 6.135,4.531 0.458,0.229 10 false ES

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C406366C08
1.5,0.125 1.885,0.385 0.385,0.26 1.375,2.042 1.156,2.042 1.156,2.042 0.885,1.385 true 1.646,1.833 1.427,1.833 1.427,1.833 0.885,1.167 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.167 1.885,0.323 0.313,0.156 10 false G18 1.708,1.74 2.198,1.938 0.49,0.198 10 false CANH 1.438,1.917 1.927,2.115 0.49,0.198 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-9 (CANH) - G18-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C406366C11
1.5,0.125 1.885,0.385 0.385,0.26 3.073,1.823 2.927,1.823 2.927,1.823 2.771,1.375 true 0.365,1.76 0.51,1.76 0.51,1.76 0.656,1.385 true 2.792,1.167 3.031,0.865 3.031,0.865 3.177,0.865 true 2.333,1.177 2.448,0.24 2.448,0.24 2.594,0.24 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.573,0.167 1.885,0.323 0.313,0.156 10 false G18 3.135,1.719 3.427,1.979 0.292,0.26 10 false IG+ 0.125,1.656 0.615,1.854 0.49,0.198 10 false ES 3.198,0.792 3.396,0.99 0.198,0.198 10 false B 2.646,0.156 2.906,0.354 0.26,0.198 10 false EP
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-23 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
G18-19 (EP) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G18-22 (B) - Body ground Power switch off 11 to 14 V
G18-38 (IG+) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR