Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0369864 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Brake booster with master cylinder assembly (skid control ECU) branch wire or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



WIRING DIAGRAM

C405897E01
5.771,0.333 6.385,0.531 0.615,0.198 10 false CA1H 5.5,0.24 6.115,0.438 0.615,0.198 10 false 37 5.792,0.813 6.406,1.01 0.615,0.198 10 false CA1L 5.5,0.708 6.115,0.906 0.615,0.198 10 false 38 5.781,5.708 6.396,5.906 0.615,0.198 10 false GND6 5.781,6.01 6.396,6.208 0.615,0.198 10 false GND5 5.781,6.313 6.396,6.51 0.615,0.198 10 false GND4 5.781,6.594 6.396,6.792 0.615,0.198 10 false GND3 5.781,6.896 6.396,7.094 0.615,0.198 10 false GND2 5.781,7.208 6.396,7.406 0.615,0.198 10 false GND 5.531,5.604 6.146,5.802 0.615,0.198 10 false 23 5.521,5.906 6.135,6.104 0.615,0.198 10 false 24 5.521,6.198 6.135,6.396 0.615,0.198 10 false 25 5.521,6.49 6.135,6.688 0.615,0.198 10 false 26 5.521,6.792 6.135,6.99 0.615,0.198 10 false 27 5.521,7.104 6.135,7.302 0.615,0.198 10 false 28 5.771,4.531 6.385,4.729 0.615,0.198 10 false IG1 5.781,3.938 6.396,4.135 0.615,0.198 10 false BS 5.781,3.333 6.396,3.531 0.615,0.198 10 false B1 5.521,4.427 6.135,4.625 0.615,0.198 10 false 16 5.521,3.823 6.135,4.021 0.615,0.198 10 false 15 5.521,3.229 6.135,3.427 0.615,0.198 10 false 14 3.802,3.156 4.719,3.344 0.917,0.188 10 false ABS NO.2 3.823,3.771 4.74,3.958 0.917,0.188 10 false ABS NO.1 3.708,4.344 4.625,4.531 0.917,0.188 10 false ECU-IG1 NO.2 1.625,3.292 3.146,3.521 1.521,0.229 10 false from Auxiliary Battery 1.625,3.896 3.146,4.125 1.521,0.229 10 false from Auxiliary Battery 1.698,5.094 3.219,5.323 1.521,0.229 10 false from IG2 NO.2 Relay 5.792,2 6.406,2.198 0.615,0.198 10 false CA2H 5.802,2.49 6.417,2.688 0.615,0.198 10 false CA2L 5.521,1.875 6.135,2.073 0.615,0.198 10 false 35 5.521,2.396 6.135,2.594 0.615,0.198 10 false 34 1.854,1.896 2.469,2.094 0.615,0.198 10 false 7 1.854,2.396 2.469,2.594 0.615,0.198 10 false 17 0.344,2.656 0.958,2.854 0.615,0.198 10 false G103 0.354,2.833 2.448,3.031 2.094,0.198 10 false No. 3 CAN Junction Connector 0.375,1.167 2.469,1.365 2.094,0.198 10 false No. 4 CAN Junction Connector 0.365,0.958 0.979,1.156 0.615,0.198 10 false G104 1.844,0.677 2.458,0.875 0.615,0.198 10 false 7 1.844,0.208 2.458,0.406 0.615,0.198 10 false 1 5.344,7.677 5.958,7.875 0.615,0.198 10 false A42 5.333,7.865 6.969,8.417 1.635,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.688,4.5 3.208,4.729 1.521,0.229 10 false from IG1 NO.1 Relay 3.688,4.938 4.604,5.125 0.917,0.188 10 false ECU-IG2 NO.3 5.521,4.99 6.135,5.188 0.615,0.198 10 false 12 5.771,5.125 6.385,5.323 0.615,0.198 10 false IG2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [SKID CONTROL ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C405903C01
1.479,0.125 1.927,0.354 0.448,0.229 1.458,2.031 1.625,2.031 1.625,2.031 1.802,1.344 true 1.344,1.833 1.51,1.833 1.51,1.833 1.708,1.313 true 2.271,2.052 2.104,2.052 2.104,2.052 1.99,1.333 true 2.354,1.844 2.188,1.844 2.188,1.844 2.094,1.323 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.583,0.167 2.042,0.365 0.458,0.198 10 false A42 1.052,1.979 1.51,2.177 0.458,0.198 10 false CA2H 0.99,1.76 1.448,1.958 0.458,0.198 10 false CA2L 2.417,1.76 2.875,1.958 0.458,0.198 10 false CA1L 2.333,1.979 2.792,2.177 0.458,0.198 10 false CA1H
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly [Skid Control ECU])


Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (CA1H) - A42-38 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A42-35 (CA2H) - A42-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C405903C02
1.479,0.125 1.927,0.354 0.448,0.229 2.219,2.063 2.385,2.063 2.385,2.063 2.385,1.063 true 2.115,1.875 2.281,1.875 2.281,1.875 2.281,1.042 true 2.656,2.052 2.49,2.052 2.49,2.052 2.49,1.052 true 2.948,1.875 2.781,1.875 2.781,1.875 2.698,1.219 true 3.01,0.281 2.844,0.281 2.844,0.281 2.698,0.969 true 2.948,0.115 2.781,0.115 2.781,0.115 2.479,0.885 true 2.458,0.125 2.625,0.125 2.625,0.125 2.302,0.917 true 1.188,2.063 1.354,2.063 1.354,2.063 2.177,1.063 true 1.083,1.844 1.25,1.844 1.25,1.844 2.073,1.042 true 1.063,0.292 1.229,0.292 1.229,0.292 1.427,0.99 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.583,0.167 2.042,0.365 0.458,0.198 10 false A42 1.792,1.979 2.25,2.177 0.458,0.198 10 false GND3 3.031,1.802 3.427,2 0.396,0.198 10 false GND 2.708,1.979 3.167,2.177 0.458,0.198 10 false GND2 1.708,1.781 2.167,1.979 0.458,0.198 10 false GND4 0.729,1.979 1.188,2.177 0.458,0.198 10 false GND5 0.667,1.771 1.125,1.969 0.458,0.198 10 false GND6 3.063,0.208 3.427,0.396 0.365,0.188 10 false BS 3,0.031 3.365,0.219 0.365,0.188 10 false B1 2.188,0.063 2.552,0.25 0.365,0.188 10 false IG2 0.802,0.219 1.167,0.406 0.365,0.188 10 false IG1
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-28 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A42-27 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A42-26 (GND3) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A42-25 (GND4) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A42-24 (GND5) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A42-23 (GND6) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
A42-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
A42-14 (B1) - Body ground Power switch off 11 to 14 V
A42-15 (BS) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR