Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) Y

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the panoramic view monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding.


Result:
Proceed to
NEXT



NEXT

4.SYSTEM CHECK
4.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Navigation System A
w/ Audio and Visual System B



A

5.CHECK NAVIGATION SYSTEM

B

6.CHECK AUDIO AND VISUAL SYSTEM
5.CHECK NAVIGATION SYSTEM

Result:
Result Proceed to
Navigation system is normal A
Navigation system is abnormal B



A

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

6.CHECK AUDIO AND VISUAL SYSTEM
a.

Refer to the audio and visual system.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PROBLEM SYMPTOMS TABLE

OK:

Audio and visual system is normal.



Result:
Result Proceed to
Audio and visual system is normal A
Audio and visual system is abnormal B



A

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

7.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

8.CHECK FOR DTC*

B

8.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

c.

Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

9.PROBLEM SYMPTOMS TABLE

B

9.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

10.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

11.ADJUST, REPAIR OR REPLACE
10.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

11.ADJUST, REPAIR OR REPLACE
11.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

12.CONFIRMATION TEST
12.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END