Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0375511 PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the Signal Check screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>DIAGNOSIS SYSTEM

HINT:
·

On the Signal Check screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the Signal Check screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch signal input state DTC is not output Panoramic view monitor switch
SHIFT*1 Vehicle wire harness Shift position signal input state DTC is not output Back-up light switch assembly
MIRROR SW*2 Vehicle wire harness Outer rear view mirror assembly signal input state DTC is not output Outer rear view mirror assembly

*1: for Manual Transaxle

*2: w/ Retract Mirror (w/o Auto Power Retract Mirror)


WIRING DIAGRAM

E403252E07
5.073,2.896 6.5,3.104 1.427,0.208 10 false Parking Assist ECU 5.146,1.76 5.896,1.979 0.75,0.219 10 false BLSW 5.135,0.542 5.885,0.76 0.75,0.219 10 false REV*1 2.052,2.229 4.188,2.521 2.135,0.292 10 false Panoramic View Monitor Switch 4.823,0.427 5.094,0.646 0.271,0.219 10 false 14 2.042,2.063 2.385,2.302 0.344,0.24 10 false G37 0.885,3.323 2.979,3.531 2.094,0.208 10 false : CAN Communication Line 5.063,2.719 5.344,2.969 0.281,0.25 10 false N25 1.115,0.552 3.615,0.792 2.5,0.24 10 false from Back-up Light Switch Assembly*1 4.833,1.635 5.104,1.854 0.271,0.219 10 false 15 3.594,1.635 3.865,1.854 0.271,0.219 10 false 5 2.167,1.646 2.438,1.865 0.271,0.219 10 false 2 3.344,1.646 3.615,1.865 0.271,0.219 10 false D 2.438,1.646 2.708,1.865 0.271,0.219 10 false E 5.135,1.156 5.885,1.375 0.75,0.219 10 false MPOS*2 4.823,1.031 5.094,1.25 0.271,0.219 10 false 16 0.344,1.698 1.771,2.052 1.427,0.354 10 false Outer Rear View Mirror Assembly LH 0.344,1.531 0.625,1.781 0.281,0.25 10 false J13 1.323,1.146 2.073,1.365 0.75,0.219 10 false MF*2 1.823,1.021 2.094,1.24 0.271,0.219 10 false 5 0.25,3 4.063,3.25 3.813,0.25 10 false *2: w/ Retract Mirror (w/o Auto Power Retract Mirror) 0.24,2.677 4.052,2.927 3.813,0.25 10 false *1: for Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the battery cable is disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for Gasoline Model)>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E403247C02
1.313,1.073 1.625,1.229 0.313,0.156 10 false *A 1.885,1.063 2.198,1.219 0.313,0.156 10 false *B 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a
*A for Manual Transaxle
*B w/ Retract Mirror (w/o Auto Power Retract Mirror)
*a Example


Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B
"SHIFT" displays "CHK" (red) (for Manual Transaxle) C
"MIRROR SW" displays "CHK" (red) (w/ Retract Mirror (w/o Auto Power Retract Mirror)) D



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)

B

C

4.CHECK BACK-UP LIGHT

D

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - PARKING ASSIST ECU)
2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the G37 panoramic view monitor switch connector.


b.

Disconnect the N25 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-5 (D) - N25-15 (BLSW) Always Below 1 Ω
G37-2 (E) - Body ground Always Below 1 Ω
G37-5 (D) or N25-15 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PANORAMIC VIEW MONITOR SWITCH
a.

Remove the panoramic view monitor switch.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>COMBINATION SWITCH>REMOVAL



Result:
Proceed to
OK
NG



OK

NG

4.CHECK BACK-UP LIGHT
a.

Check that the back-up light comes on.

OK:

The back-up light comes on.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

5.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.
E362888C03
1.438,0.292 1.979,0.531 0.542,0.24 2.615,1.76 2.365,1.76 2.365,1.76 2.281,1.26 true 2.677,1.656 3.104,1.854 0.427,0.198 10 false REV 0.083,0.063 0.51,0.26 0.427,0.198 10 false *a 1.563,0.323 1.99,0.521 0.427,0.198 10 false N25
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N25-14 (REV) - Body ground Engine switch on (IG), shift lever in R 11 to 14 V
N25-14 (REV) - Body ground Engine switch on (IG), shift lever not in R Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - PARKING ASSIST ECU)
a.

Disconnect the J13 outer rear view mirror assembly LH connector.


b.

Disconnect the N25 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-5 (MF) - N25-16 (MPOS) Always Below 1 Ω
J13-5 (MF) or N25-16 (MPOS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR