Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM
RM3620E _52 Drivetrain _076960 GF1A TRANSFER / 4WD / AWD _0379782 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C1297  Steering Angle Sensor  


DESCRIPTION

·

The 4WD ECU assembly determines that the vehicle is turning based on the signals sent from the steering sensor.

·

The steering sensor signal is sent to the 4WD ECU assembly via the CAN communication system.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1297 Steering Angle Sensor When voltage of 4WD ECU assembly IG terminal is 9.5 V or more, and steering sensor malfunction signal is received.
·

ECU-IG1 NO.2 fuse*1

·

ECU-DCC NO.1 fuse

·

Steering sensor

·

CAN communication system

·

4WD ECU assembly

·

Wire harness or connector

·

Backup boost converter circuit*2



*1: w/o Stop and Start System

*2: w/ Stop and Start System

WIRING DIAGRAM

C279156E10
3.854,3.01 5.948,3.365 2.094,0.354 10 false Steering Sensor 0.781,3.198 2.521,3.396 1.74,0.198 10 false : CAN Communication Line 2.542,1.729 3.5,1.917 0.958,0.188 10 false ECU-IG1 NO.2 2.5,2.135 3.677,2.354 1.177,0.219 10 false ECU-DCC NO.1 4.01,1.583 4.333,1.781 0.323,0.198 10 false IG1 3.813,1.688 4.01,1.917 0.198,0.229 10 false 9 3.813,2.094 4.125,2.302 0.313,0.208 10 false 4 3.792,2.479 4.01,2.677 0.219,0.198 10 false 6 3.865,2.802 4.323,3 0.458,0.198 10 false G68 4.021,1.99 4.479,2.188 0.458,0.198 10 false BAT 3.99,2.396 4.448,2.594 0.458,0.198 10 false ESS 5.677,2.063 7.042,2.292 1.365,0.229 10 false 4WD ECU Assembly 3.313,1.479 3.625,1.677 0.313,0.198 10 false *3 2.854,0.51 3.167,0.708 0.313,0.198 10 false *4 0.083,2.583 2.125,2.781 2.042,0.198 10 false *3: w/o Stop and Start System 0.083,2.885 2,3.073 1.917,0.188 10 false *4: w/ Stop and Start System 0.708,0.625 1.083,0.823 0.375,0.198 10 false IG31 1.146,0.729 1.458,0.927 0.313,0.198 10 false 1 0.083,1.292 1.146,1.667 1.063,0.375 10 false Engine Stop and Start ECU*4 0.094,1.115 1.479,1.313 1.385,0.198 10 false A32*1 G62*2 1.24,1.573 2.146,1.76 0.906,0.188 10 false from IG Circuit 1.354,1.948 2.156,2.135 0.802,0.188 10 false from Battery 0.083,2.083 2,2.271 1.917,0.188 10 false *1: for LHD 0.083,2.333 2,2.521 1.917,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC(s) is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (24 mph), turn the steering wheel to the right and left and check that no electronically controlled brake system (steering sensor) DTC (C1432, C1433 or C1434) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
Neither CAN communication system DTC nor electronically controlled brake system DTC is output A
CAN communication system DTC is output B
Electronically controlled brake system (steering sensor) DTC (C1432, C1433 or C1434) is output C


HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.




A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C374262C58
0.229,0.771 0.615,1.01 0.385,0.24 2,1.99 2.604,1.635 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.302,0.813 0.76,1.01 0.458,0.198 10 false G68 2.667,1.552 3.125,1.75 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Remove the steering wheel and the column cover lower.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the steering sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G68-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch to ON.


b.
C374262C60
0.229,0.771 0.615,1.01 0.385,0.24 2.021,2.365 2.521,2.667 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.302,0.813 0.76,1.01 0.458,0.198 10 false G68 2.604,2.688 3.063,2.885 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Sensor)


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/ Stop and Start System

*2: w/o Stop and Start System

G68-9 (IG1) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

NG (w/ Stop and Start System)

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-6 (ESS) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STEERING ANGLE VALUE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (STEERING ANGLE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


e.

Read the value displayed on the GTS.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Angle Value Steering angle value Min.: -3276.8°
Max.: 3276.7°
Left turn: Increase
Right turn: Decrease
Changes in proportion with the amount of steering wheel rotation during steering operation.
Chassis > Four Wheel Drive > Data List
Tester Display
Steering Angle Value
50003 118 8
OK:

The steering sensor value changes in accordance with the steering wheel movement.



Result:
Proceed to
OK
NG



OK

NG