Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379920 AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System)  B162A  Side Airbag Sensor Assembly No.2 (RH)  


DESCRIPTION

The side collision sensor RH circuit consists of the airbag sensor assembly and floor side airbag sensor RH.

The floor side airbag sensor RH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.

DTC B162A is stored when a malfunction is detected in the floor side airbag sensor RH or airbag sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B162A Side Airbag Sensor Assembly No.2 (RH) Either condition is met:
·

A floor side airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor side airbag sensor RH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C370759E36
1.24,2.094 1.698,2.25 0.458,0.156 10 false BFR- 1.24,0.927 1.698,1.083 0.458,0.156 10 false BFR+ 1.75,0.802 1.958,0.979 0.208,0.177 10 false 2 1.719,1.969 1.927,2.115 0.208,0.146 10 false 1 0.333,2.802 0.656,2.99 0.323,0.188 10 false M17 0.313,2.958 3.24,3.281 2.927,0.323 10 false Floor Side Airbag Sensor RH 5.323,0.802 5.615,0.99 0.292,0.188 10 false 28 5.333,1.969 5.583,2.156 0.25,0.188 10 false 27 5.615,0.917 6.115,1.083 0.5,0.167 10 false BCR+ 5.615,2.083 6.104,2.26 0.49,0.177 10 false BCR- 5.49,2.781 6.26,3.052 0.771,0.271 10 false M15 5.5,2.927 7.125,3.302 1.625,0.375 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK FLOOR SIDE AIRBAG SENSOR RH
a.
C374693C24
0.969,1.583 1.24,1.781 0.271,0.198 10 false *1 2.49,1.396 2.76,1.594 0.271,0.198 10 false *2
*1 Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the floor side airbag sensor RH with LH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the engine switch off.


h.

Turn the engine switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B162A is output
DTC B163A is output
DTCs B162A and B163A are not output


HINT:

Codes other than DTCs B162A and B163A may be output at this time, but they are not related to this check.



j.

Turn the engine switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the floor side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B162A is output

DTC B163A is output

DTCs B162A and B163A are not output