Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System) › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379920 AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System)  B1638  Curtain Shield Airbag Sensor Initialization Error (LH)  


DESCRIPTION

The side collision sensor LH circuit consists of the airbag sensor assembly, side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH.

The No. 2 side airbag sensor assembly LH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.

DTC B1638 is stored when a malfunction is detected in the circuit for the side collision sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1638 Curtain Shield Airbag Sensor Initialization Error (LH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A No. 2 side airbag sensor assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire LH

·

No. 2 side airbag sensor assembly LH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C401868E26
5.375,2.083 7.01,2.323 1.635,0.24 10 false Airbag Sensor Assembly 5.375,1.927 6.208,2.125 0.833,0.198 10 false N21 5.677,0.875 6.51,1.073 0.833,0.198 10 false BBL+ 5.698,1.458 6.531,1.656 0.833,0.198 10 false BBL- 5.406,0.76 6.24,0.958 0.833,0.198 10 false 32 5.406,1.365 6.24,1.563 0.833,0.198 10 false 31 1.615,0.75 2.448,0.948 0.833,0.198 10 false 4 1.635,1.313 2.469,1.51 0.833,0.198 10 false 3 1.146,0.854 1.979,1.052 0.833,0.198 10 false BCL+ 1.104,1.469 1.938,1.667 0.833,0.198 10 false BCL- 1.135,2.792 1.969,2.99 0.833,0.198 10 false BDL+ 1.146,3.333 1.979,3.531 0.833,0.198 10 false BDL- 1.604,2.688 2.438,2.885 0.833,0.198 10 false 1 1.594,3.24 2.427,3.438 0.833,0.198 10 false 2 4.083,2.813 4.917,3.01 0.833,0.198 10 false BDL+ 4.094,3.354 4.927,3.552 0.833,0.198 10 false BDL- 0.552,3.969 2.177,4.354 1.625,0.385 10 false No. 2 Side Airbag Sensor Assembly LH 0.542,3.813 1.302,4.146 0.76,0.333 10 false N22 4.01,3.979 6.094,4.188 2.083,0.208 10 false Side Airbag Pressure Sensor LH 4.021,3.823 4.781,4.156 0.76,0.333 10 false J9 2.698,3.344 3.458,3.677 0.76,0.333 10 false JN2 2.708,2.813 3.469,3.146 0.76,0.333 10 false JN2 2.781,3.156 3.615,3.354 0.833,0.198 10 false 2 2.781,2.594 3.615,2.792 0.833,0.198 10 false 1 3.906,2.719 4.74,2.917 0.833,0.198 10 false 2 3.906,3.26 4.74,3.458 0.833,0.198 10 false 1 2.698,2.99 3.531,3.188 0.833,0.198 10 false BDL+ 2.688,3.563 3.521,3.76 0.833,0.198 10 false BDL-

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK PAST DTC
a.

Turn the engine switch on (IG), and wait for at least 60 seconds.



Result:
Proceed to
DTC B1637 is not output
DTC B1637 is output



DTC B1637 is not output

2.CHECK CONNECTION OF CONNECTORS

DTC B1637 is output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and No. 2 side airbag sensor assembly LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and No. 2 side airbag sensor assembly LH.


b.
C208244C47
0.656,1.344 0.969,1.542 0.313,0.198 10 false *1 1.531,0.604 1.844,0.802 0.313,0.198 10 false *3 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and No. 2 side airbag sensor assembly LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK FLOOR WIRE

The connectors are deformed or damaged

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE
a.
C411582C03
0.948,3.458 1.438,3.698 0.49,0.24 2.521,0.604 3.01,0.844 0.49,0.24 1.406,1.25 1.583,1.25 1.583,1.25 1.875,0.781 true 2.479,1.219 2.292,1.219 2.292,1.219 2.094,0.771 true 2.698,3.719 2.563,3.719 2.563,3.719 2.354,3.844 true 2.719,3.406 2.615,3.406 2.615,3.406 2.26,3.854 true 2.604,4.396 2.469,4.396 2.469,4.396 2.313,4.25 true 0.438,2.365 0.75,2.521 0.313,0.156 10 false *1 2.688,1.594 3,1.75 0.313,0.156 10 false *2 1.5,2.073 1.813,2.229 0.313,0.156 10 false *3 2.677,4.281 2.99,4.438 0.313,0.156 10 false *4 0.771,0.24 1.083,0.396 0.313,0.156 10 false *a 0.969,2.99 1.281,3.146 0.313,0.156 10 false *b 1.063,3.5 1.375,3.656 0.313,0.156 10 false N21 2.635,0.635 2.948,0.792 0.313,0.156 10 false N22 2.281,1.885 2.594,2.042 0.313,0.156 10 false A 1.99,1.875 2.302,2.031 0.313,0.156 10 false B 1.021,1.885 1.333,2.042 0.313,0.156 10 false C 0.719,1.875 1.031,2.031 0.313,0.156 10 false D 2.552,1.135 2.979,1.344 0.427,0.208 10 false BCL+ 1.042,1.146 1.469,1.354 0.427,0.208 10 false BCL- 2.771,3.646 3.198,3.854 0.427,0.208 10 false BBL+ 2.771,3.313 3.198,3.521 0.427,0.208 10 false BBL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N22-4 (BCL+) - Body ground Engine switch on (IG) Below 1 V
N22-3 (BCL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N22-4 (BCL+) - N22-3 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N22-4 (BCL+) - N22-3 (BCL-) Always 1 MΩ or higher
N22-4 (BCL+) - Body ground Always 1 MΩ or higher
N22-3 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C370762C25
0.875,0.938 1.188,1.135 0.313,0.198 10 false *1 2.406,1.313 2.719,1.51 0.313,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the engine switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1638 is output
DTC B1633 is output
DTCs B1633 and B1638 are not output


HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the No. 2 side airbag sensor assembly RH and LH to their original positions and connect the connectors to them.



DTC B1638 is output

6.CHECK CONNECTION OF CONNECTOR

DTC B1633 is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

DTCs B1633 and B1638 are not output

6.CHECK CONNECTION OF CONNECTOR
a.

Check that the connector is properly connected to the side airbag pressure sensor LH.


Result:
Proceed to
The connector is properly connected
The connector is not properly connected



The connector is properly connected

7.CHECK CONNECTOR

The connector is not properly connected

CONNECT CONNECTOR PROPERLY

7.CHECK CONNECTOR
a.

Disconnect the connectors from the side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH.


b.
C306644C19
0.604,1.5 0.917,1.656 0.313,0.156 10 false *1 2.604,1.5 2.917,1.656 0.313,0.156 10 false *2 1.417,1.25 1.729,1.406 0.313,0.156 10 false *3 1.854,1.25 2.167,1.406 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire


Check that the connector (on the side airbag pressure sensor LH side) is not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

8.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT

The connector is deformed or damaged

REPLACE FRONT DOOR WIRE LH

8.CHECK SIDE AIRBAG PRESSURE SENSOR LH CIRCUIT
a.
C411584C03
0.74,0.813 1.24,1.052 0.5,0.24 2.458,2.875 2.958,3.115 0.5,0.24 1.271,1.521 1.438,1.521 1.438,1.521 1.677,0.99 true 2.5,1.5 2.323,1.5 2.323,1.5 2.01,0.969 true 1,3.344 1.167,3.344 1.167,3.344 1.646,3.667 true 1.438,2.938 1.573,2.938 1.573,2.938 1.844,3.552 true 1.875,4.135 2.094,4.281 2.094,4.281 2.25,4.281 true 0.448,2.583 0.76,2.74 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.229,2.302 1.542,2.458 0.313,0.156 10 false *3 1.792,2.333 2.104,2.49 0.313,0.156 10 false *4 0.781,0.292 1.094,0.448 0.313,0.156 10 false *a 0.521,2.865 0.833,3.021 0.313,0.156 10 false *b 0.917,0.844 1.229,1 0.313,0.156 10 false J9 2.396,2.125 2.708,2.281 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.625,2.125 1.938,2.281 0.313,0.156 10 false C 1.469,2.115 1.781,2.271 0.313,0.156 10 false D 1.031,2.115 1.344,2.271 0.313,0.156 10 false E 0.708,2.125 1.021,2.281 0.313,0.156 10 false F 2.583,2.906 2.917,3.146 0.333,0.24 10 false N22 2.573,1.406 3.135,1.667 0.563,0.26 10 false BDL+ 0.885,1.427 1.448,1.688 0.563,0.26 10 false BDL- 1.052,2.844 1.615,3.104 0.563,0.26 10 false BDL- 0.563,3.25 1.125,3.51 0.563,0.26 10 false BDL+ 2.333,4.198 2.646,4.354 0.313,0.156 10 false *5
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J9-2 (BDL+) - Body ground Engine switch on (IG) Below 1 V
J9-1 (BDL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-2 (BDL+) - J9-1 (BDL-) Always 1 MΩ or higher
J9-2 (BDL+) - Body ground Always 1 MΩ or higher
J9-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.CHECK CONNECTORS
9.CHECK DTC
a.
C238395C22
0.729,1.563 1,1.74 0.271,0.177 10 false *1 2.583,1.542 2.896,1.75 0.313,0.208 10 false *2
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH


Connect the connectors to the side airbag pressure sensor LH and No. 2 side airbag sensor assembly LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the engine switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1638 is output
DTC B1638 is not output


HINT:

Codes other than DTC B1638 may be output at this time, but they are not related to this check.




DTC B1638 is output

DTC B1638 is not output

10.CHECK CONNECTORS
a.
B510595C03
0.458,1.479 0.771,1.635 0.313,0.156 10 false *1 2.823,1.5 3.135,1.656 0.313,0.156 10 false *2 1.25,1.229 1.563,1.385 0.313,0.156 10 false *3 2.021,1.24 2.333,1.396 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire LH.


b.

Check that the connectors (on the floor wire side and front door wire LH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

11.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

11.CHECK FLOOR WIRE
a.
C411586C03
0.594,3.5 0.927,3.75 0.333,0.25 1.188,0.844 1.51,1.083 0.323,0.24 2.885,1 2.75,1 2.75,1 2.323,0.656 true 1.438,0.479 1.635,0.479 1.635,0.479 2.063,0.771 true 1.823,3.073 1.698,3.073 1.698,3.073 1.615,3.594 true 2.51,3.063 2.385,3.063 2.385,3.063 1.802,3.594 true 2.115,4.396 2,4.396 2,4.396 1.854,4.156 true 0.167,0.177 0.479,0.385 0.313,0.208 10 false *a 1.229,0.875 1.542,1.083 0.313,0.208 10 false JN2 2.563,2.26 2.781,2.479 0.219,0.219 10 false A 2.24,2.271 2.458,2.49 0.219,0.219 10 false B 1.792,2.271 2.01,2.49 0.219,0.219 10 false C 1.479,2.271 1.698,2.49 0.219,0.219 10 false D 1.031,2.271 1.25,2.49 0.219,0.219 10 false E 0.719,2.271 0.938,2.49 0.219,0.219 10 false F 0.385,2.719 0.698,2.927 0.313,0.208 10 false *1 1.229,2.479 1.542,2.688 0.313,0.208 10 false *3 2.771,2.708 3.083,2.917 0.313,0.208 10 false *2 1.99,2.458 2.302,2.667 0.313,0.208 10 false *4 0.542,3.031 0.854,3.24 0.313,0.208 10 false *b 0.646,3.531 0.958,3.74 0.313,0.208 10 false N22 2.958,0.917 3.375,1.271 0.417,0.354 10 false BDL+ 1.063,0.385 1.573,0.594 0.51,0.208 10 false BDL- 1.896,2.99 2.406,3.198 0.51,0.208 10 false BDL+ 2.573,2.979 3.083,3.188 0.51,0.208 10 false BDL- 2.188,4.313 2.5,4.521 0.313,0.208 10 false *5
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JN2-1 (BDL+) - Body ground Engine switch on (IG) Below 1 V
JN2-2 (BDL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JN2-1 (BDL+) - JN2-2 (BDL-) Always 1 MΩ or higher
JN2-1 (BDL+) - Body ground Always 1 MΩ or higher
JN2-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE