The side collision sensor LH circuit consists of the airbag sensor assembly and floor side airbag sensor LH.
The floor side airbag sensor LH detects impacts to the vehicle and send signals to the airbag sensor assembly to determine if the SRS should be deployed.
These DTCs are stored when a malfunction is detected in the No. 2 side collision sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B163B | Side Airbag Sensor Assembly No.2 Lost Communication (LH) | One of the following conditions is met:
·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit. ·
A floor side airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Floor wire ·
Floor side airbag sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
| B163C | Side Airbag Sensor Assembly No.2 Initialization Error (LH) | One of the following conditions is met:
·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit. ·
A floor side airbag sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
Floor wire ·
Floor side airbag sensor LH ·
Airbag sensor assembly |
Comes on | Not applicable |
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and floor side airbag sensor LH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and floor side airbag sensor LH.
| *1 | Floor Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
Check that the connectors (on the airbag sensor assembly side and floor side airbag sensor LH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
| *1 | Floor Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Floor Side Airbag Sensor LH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N23-2 (BFL+) - Body ground | Engine switch on (IG) | Below 1 V |
| N23-1 (BFL-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (BCL+) and 30 (BCL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-2 (BFL+) - N23-1 (BFL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-2 (BFL+) - N23-1 (BFL-) | Always | 1 MΩ or higher |
| N23-2 (BFL+) - Body ground | Always | 1 MΩ or higher |
| N23-1 (BFL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the airbag sensor assembly.
| *1 | Floor Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Interchange the floor side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B163B or B163C is output |
| DTC B162B or B162C is output |
| DTCs B162B, B162C, B163B and B163C are not output |
Codes other than DTC B162B, B162C, B163B and B163C may be output at this time, but they are not related to this check.
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the floor side airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B163B or B163C is output
DTC B162B or B162C is output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Center Pillar)>REMOVAL
DTCs B162B, B162C, B163B and B163C are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING