Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379920 AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Gasoline Model with Occupant Classification System)  B1656  Seat Belt Buckle Switch (LH)  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag sensor assembly and front seat inner belt assembly LH.

DTC B1656 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1656 Seat Belt Buckle Switch (LH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch LH circuit.

·

A front seat inner belt assembly LH (seat belt buckle switch LH) malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat inner belt assembly LH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C239223E57
1.667,0.76 2.375,1.365 0.708,0.604 10 false LBE+ 1.688,2.198 2.365,2.677 0.677,0.479 10 false LBE- 5.406,0.896 5.833,1.333 0.427,0.438 10 false LBE+ 5.406,2.073 5.865,2.5 0.458,0.427 10 false LBE- 2.135,0.781 2.5,1.24 0.365,0.458 10 false 2 2.125,1.958 2.458,2.375 0.333,0.417 10 false 1 5.125,0.802 5.5,1.333 0.375,0.531 10 false 28 5.135,1.958 5.448,2.365 0.313,0.406 10 false 27 0.552,2.917 1.365,3.302 0.813,0.385 10 false N35 0.552,3.073 2.729,3.573 2.177,0.5 10 false Front Seat Inner Belt Assembly LH 5.323,2.906 5.74,3.344 0.417,0.438 10 false N21 5.323,3.073 6.958,3.479 1.635,0.406 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

2.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C208244C48
0.656,1.354 0.969,1.552 0.313,0.198 10 false *1 2.563,1.781 2.875,1.979 0.313,0.198 10 false *2 1.531,0.594 1.844,0.792 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.


b.

Check that the connectors (on the airbag sensor assembly side and front seat inner belt assembly LH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

3.CHECK FLOOR WIRE

Connectors are deformed or damaged

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
a.
C411482C03
0.854,3.552 1.323,3.771 0.469,0.219 0.729,0.656 1.135,0.885 0.406,0.229 2.521,0.531 2.375,0.531 2.375,0.531 2,0.802 true 1.76,0.833 1.396,1.156 1.396,1.156 1.281,1.156 true 1.938,4.031 2.521,3.74 2.521,3.74 2.656,3.74 true 1.865,4.031 2.49,3.24 2.49,3.24 2.615,3.24 true 1.99,4.25 2.552,4.396 2.552,4.396 2.667,4.396 true 0.438,2.479 0.75,2.635 0.313,0.156 10 false *1 2.823,2.844 3.135,3 0.313,0.156 10 false *2 1.542,2.167 1.854,2.323 0.313,0.156 10 false *3 2.74,4.313 3.052,4.469 0.313,0.156 10 false *4 0.75,0.229 1.063,0.385 0.313,0.156 10 false *a 0.708,3.125 1.021,3.281 0.313,0.156 10 false *b 0.969,3.583 1.281,3.74 0.313,0.156 10 false N21 0.802,0.688 1.115,0.844 0.313,0.156 10 false N35 2.677,3.167 3.083,3.333 0.406,0.167 10 false LBE- 2.615,0.448 3.021,0.615 0.406,0.167 10 false LBE+ 0.927,1.073 1.333,1.24 0.406,0.167 10 false LBE- 2.719,3.667 3.125,3.833 0.406,0.167 10 false LBE+ 2.375,1.948 2.688,2.104 0.313,0.156 10 false A 2.073,1.969 2.385,2.125 0.313,0.156 10 false B 1.01,1.969 1.323,2.125 0.313,0.156 10 false C 0.719,1.969 1.031,2.125 0.313,0.156 10 false D
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N35-1 (LBE-) - Body ground Engine switch on (IG) Below 1 V
N35-2 (LBE+) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 28 (LBE+) and 27 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N35-1 (LBE-) - N35-2 (LBE+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N35-1 (LBE-) - N35-2 (LBE+) Always 1 MΩ or higher
N35-1 (LBE-) - Body ground Always 1 MΩ or higher
N35-2 (LBE+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C370762C14
0.854,0.927 1.167,1.125 0.313,0.198 10 false *1 2.406,1.292 2.719,1.49 0.313,0.198 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the engine switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1656 is not output
DTC B1656 is output


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




DTC B1656 is output

5.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

DTC B1656 is not output

5.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle if possible.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.
C370762C14
0.854,0.927 1.167,1.125 0.313,0.198 10 false *1 2.406,1.292 2.719,1.49 0.313,0.198 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the engine switch on (IG), and wait for at least 60 seconds.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1656 is not output
DTC B1656 is output


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




DTC B1656 is not output

END (FRONT SEAT INNER BELT ASSEMBLY LH WAS DEFECTIVE)

DTC B1656 is output