Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/o Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0378287 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1630  Curtain Shield Airbag Sensor (RH)  B1632  Curtain Shield Airbag Sensor Lost Communication (RH)  


DESCRIPTION

The side collision sensor RH circuit consists of the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.

The No. 2 side airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the No. 2 side airbag sensor assembly RH or airbag sensor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1630 Curtain Shield Airbag Sensor (RH) Either condition is met:
·

A No. 2 side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Not applicable
B1632 Curtain Shield Airbag Sensor Lost Communication (RH) Either condition is met:
·

A No. 2 side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C401868E27
5.375,2.083 6.969,2.365 1.594,0.281 10 false Airbag Sensor Assembly 5.375,1.927 6.208,2.125 0.833,0.198 10 false M15 5.677,0.875 6.51,1.073 0.833,0.198 10 false BBR+ 5.698,1.458 6.531,1.656 0.833,0.198 10 false BBR- 5.406,0.76 6.24,0.958 0.833,0.198 10 false 25 5.406,1.365 6.24,1.563 0.833,0.198 10 false 26 1.615,0.75 2.448,0.948 0.833,0.198 10 false 4 1.635,1.313 2.469,1.51 0.833,0.198 10 false 3 1.146,0.854 1.979,1.052 0.833,0.198 10 false BCR+ 1.104,1.469 1.938,1.667 0.833,0.198 10 false BCR- 1.135,2.792 1.969,2.99 0.833,0.198 10 false BDR+ 1.146,3.333 1.979,3.531 0.833,0.198 10 false BDR- 1.604,2.688 2.438,2.885 0.833,0.198 10 false 1 1.594,3.24 2.427,3.438 0.833,0.198 10 false 2 4.083,2.813 4.917,3.01 0.833,0.198 10 false BDR+ 4.094,3.354 4.927,3.552 0.833,0.198 10 false BDR- 0.552,3.969 2.177,4.354 1.625,0.385 10 false No. 2 Side Airbag Sensor Assembly RH 0.552,3.813 1.313,4.146 0.76,0.333 10 false M16 4.01,3.979 6.083,4.219 2.073,0.24 10 false Side Airbag Pressure Sensor RH 4.021,3.823 4.781,4.156 0.76,0.333 10 false I10 2.698,3.344 3.458,3.677 0.76,0.333 10 false IM2 2.708,2.813 3.469,3.146 0.76,0.333 10 false IM2 2.781,3.167 3.615,3.365 0.833,0.198 10 false 2 2.781,2.594 3.615,2.792 0.833,0.198 10 false 1 2.667,2.99 3.5,3.188 0.833,0.198 10 false BDR+ 2.708,3.552 3.542,3.75 0.833,0.198 10 false BDR- 3.906,2.708 4.74,2.906 0.833,0.198 10 false 2 3.906,3.219 4.74,3.417 0.833,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C374693C24
0.969,1.583 1.24,1.781 0.271,0.198 10 false *1 2.49,1.396 2.76,1.594 0.271,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors to them.


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1630 or B1632 is output
DTC B1635 or B1637 is output
DTCs B1630, B1632, B1635 and B1637 are not output


HINT:

Codes other than DTC B1630, B1632, B1635 and B1637 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


l.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B1630 or B1632 is output

DTC B1635 or B1637 is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

DTCs B1630, B1632, B1635 and B1637 are not output