Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/o Occupant Classification System) › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0378287 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B166D  Lost Communication with Front Door Pressure Sensor RH  B166E  Front Door Pressure Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit consists of the airbag sensor assembly, side airbag pressure sensor RH and No. 2 side airbag sensor assembly RH.

The side airbag pressure sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.

These DTCs are stored when a malfunction is detected in the circuit for the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B166D Lost Communication with Front Door Pressure Sensor RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A side airbag pressure sensor RH malfunction.

·

A No. 2 side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag pressure sensor RH

·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Not applicable
B166E Front Door Pressure Sensor RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A side airbag pressure sensor RH malfunction.

·

A No. 2 side airbag sensor assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front door wire RH

·

Side airbag pressure sensor RH

·

No. 2 side airbag sensor assembly RH

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C401868E34
5.375,2.083 7.021,2.667 1.646,0.583 10 false Airbag Sensor Assembly 5.375,1.927 6.208,2.125 0.833,0.198 10 false M15 5.677,0.875 6.51,1.073 0.833,0.198 10 false BBR+ 5.698,1.458 6.531,1.656 0.833,0.198 10 false BBR- 5.406,0.76 6.24,0.958 0.833,0.198 10 false 25 5.406,1.365 6.24,1.563 0.833,0.198 10 false 26 1.615,0.75 2.448,0.948 0.833,0.198 10 false 4 1.635,1.313 2.469,1.51 0.833,0.198 10 false 3 1.146,0.854 1.979,1.052 0.833,0.198 10 false BCR+ 1.104,1.469 1.938,1.667 0.833,0.198 10 false BCR- 1.135,2.792 1.969,2.99 0.833,0.198 10 false BDR+ 1.146,3.333 1.979,3.531 0.833,0.198 10 false BDR- 1.604,2.688 2.438,2.885 0.833,0.198 10 false 1 1.594,3.24 2.427,3.438 0.833,0.198 10 false 2 4.083,2.813 4.917,3.01 0.833,0.198 10 false BDR+ 4.094,3.354 4.927,3.552 0.833,0.198 10 false BDR- 0.552,3.969 2.177,4.365 1.625,0.396 10 false No. 2 Side Airbag Sensor Assembly RH 0.552,3.813 1.313,4.146 0.76,0.333 10 false M16 4.01,3.979 6.156,4.292 2.146,0.313 10 false Side Airbag Pressure Sensor RH 4.021,3.823 4.781,4.156 0.76,0.333 10 false I10 2.698,3.344 3.458,3.677 0.76,0.333 10 false IM2 2.708,2.813 3.469,3.146 0.76,0.333 10 false IM2 2.781,3.167 3.615,3.365 0.833,0.198 10 false 2 2.781,2.594 3.615,2.792 0.833,0.198 10 false 1 2.667,2.99 3.5,3.188 0.833,0.198 10 false BDR+ 2.708,3.552 3.542,3.75 0.833,0.198 10 false BDR- 3.906,2.708 4.74,2.906 0.833,0.198 10 false 2 3.906,3.219 4.74,3.417 0.833,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the No. 2 side airbag sensor assembly RH and side airbag pressure sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C301835C21
0.604,1.458 0.917,1.615 0.313,0.156 10 false *1 2.573,1.469 2.885,1.625 0.313,0.156 10 false *2 1.385,0.802 1.698,0.958 0.313,0.156 10 false *3 1.896,0.792 2.208,0.948 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the connectors from the No. 2 side airbag sensor assembly RH and side airbag pressure sensor RH.


b.

Check that the connectors (on the No. 2 side airbag sensor assembly RH side and side airbag pressure sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FRONT DOOR WIRE RH OR FLOOR WIRE

3.CHECK SIDE AIRBAG PRESSURE SENSOR RH CIRCUIT
a.
C411558C01
0.771,0.813 1.167,1.031 0.396,0.219 2.427,2.875 2.844,3.104 0.417,0.229 1.313,1.5 1.479,1.5 1.479,1.5 1.719,0.969 true 2.406,1.5 2.229,1.5 2.229,1.5 1.917,0.969 true 0.917,3.375 1.042,3.375 1.042,3.375 1.573,3.563 true 1.354,2.948 1.521,2.948 1.521,2.948 1.74,3.552 true 1.865,4.073 2.083,4.219 2.083,4.219 2.24,4.219 true 0.448,2.583 0.76,2.74 0.313,0.156 10 false *1 2.635,2.583 2.948,2.74 0.313,0.156 10 false *2 1.229,2.302 1.542,2.458 0.313,0.156 10 false *3 1.792,2.333 2.104,2.49 0.313,0.156 10 false *4 0.781,0.292 1.094,0.448 0.313,0.156 10 false *a 0.531,2.927 0.844,3.083 0.313,0.156 10 false *b 0.875,0.844 1.188,1 0.313,0.156 10 false I10 2.396,2.125 2.708,2.281 0.313,0.156 10 false A 2.073,2.125 2.385,2.281 0.313,0.156 10 false B 1.625,2.125 1.938,2.281 0.313,0.156 10 false C 1.469,2.115 1.781,2.271 0.313,0.156 10 false D 1.031,2.115 1.344,2.271 0.313,0.156 10 false E 0.708,2.125 1.021,2.281 0.313,0.156 10 false F 2.5,2.906 2.813,3.063 0.313,0.156 10 false M16 2.479,1.385 3.042,1.646 0.563,0.26 10 false BDR+ 0.938,1.385 1.5,1.646 0.563,0.26 10 false BDR- 0.979,2.854 1.542,3.115 0.563,0.26 10 false BDR- 0.51,3.302 1.073,3.563 0.563,0.26 10 false BDR+ 2.313,4.146 2.625,4.302 0.313,0.156 10 false *5
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I10-2 (BDR+) - Body ground Ignition switch ON Below 1 V
I10-1 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I10-2 (BDR+) - I10-1 (BDR-) Always 1 MΩ or higher
I10-2 (BDR+) - Body ground Always 1 MΩ or higher
I10-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SIDE AIRBAG PRESSURE SENSOR RH

NG

6.CHECK CONNECTORS
4.CHECK SIDE AIRBAG PRESSURE SENSOR RH
a.
C238395C07
0.729,1.563 1,1.74 0.271,0.177 10 false *1 2.583,1.542 2.896,1.75 0.313,0.208 10 false *2
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor Assembly RH


Connect the connector to the No. 2 side airbag sensor assembly RH.


b.

Interchange the side airbag pressure sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B166D or B166E is output
DTC B167B or B167C is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors to them.



DTC B166D or B166E is output

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

DTC B167B or B167C is output

DTCs B166D, B166E, B167B and B167C are not output

5.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.

Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors to them.


C374693C26
0.969,1.583 1.24,1.781 0.271,0.198 10 false *1 2.49,1.396 2.76,1.594 0.271,0.198 10 false *2
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B166D or B166E is output
DTC B167B or B167C is output
DTCs B166D, B166E, B167B and B167C are not output


HINT:

Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


j.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors to them.



DTC B166D or B166E is output

DTC B167B or B167C is output

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

DTCs B166D, B166E, B167B and B167C are not output

6.CHECK CONNECTORS
a.
B510595C02
0.458,1.479 0.771,1.635 0.313,0.156 10 false *1 2.823,1.5 3.135,1.656 0.313,0.156 10 false *2 1.25,1.229 1.563,1.385 0.313,0.156 10 false *3 2.021,1.24 2.333,1.396 0.313,0.156 10 false *4
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire


Disconnect the floor wire connector from the front door wire RH.


b.

Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.


Result:
Proceed to
The connector is not deformed or damaged
The connector is deformed or damaged



The connector is not deformed or damaged

7.CHECK FLOOR WIRE

The connector is deformed or damaged

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

7.CHECK FLOOR WIRE
a.
C411586C09
0.583,3.5 0.99,3.75 0.406,0.25 0.969,0.854 1.292,1.094 0.323,0.24 1.646,0.51 1.844,0.51 1.844,0.51 2.104,0.719 true 1.854,3.052 1.729,3.052 1.729,3.052 1.646,3.573 true 2.521,3.063 2.396,3.063 2.396,3.063 1.813,3.594 true 2.115,4.354 2,4.354 2,4.354 1.854,4.115 true 2.896,1.094 2.781,1.094 2.781,1.094 2.281,0.76 true 0.167,0.177 0.479,0.385 0.313,0.208 10 false *a 1.021,0.896 1.333,1.104 0.313,0.208 10 false IM2 2.563,2.26 2.781,2.479 0.219,0.219 10 false A 2.24,2.271 2.458,2.49 0.219,0.219 10 false B 1.792,2.271 2.01,2.49 0.219,0.219 10 false C 1.479,2.271 1.698,2.49 0.219,0.219 10 false D 1.031,2.271 1.25,2.49 0.219,0.219 10 false E 0.719,2.271 0.938,2.49 0.219,0.219 10 false F 0.385,2.719 0.698,2.927 0.313,0.208 10 false *1 1.229,2.479 1.542,2.688 0.313,0.208 10 false *3 2.771,2.708 3.083,2.917 0.313,0.208 10 false *2 1.99,2.458 2.302,2.667 0.313,0.208 10 false *4 0.542,3.031 0.854,3.24 0.313,0.208 10 false *b 0.656,3.542 0.969,3.75 0.313,0.208 10 false M16 2.948,1 3.365,1.313 0.417,0.313 10 false BDR+ 1.292,0.417 1.688,0.615 0.396,0.198 10 false BDR- 1.875,2.979 2.385,3.188 0.51,0.208 10 false BDR+ 2.542,2.979 3.052,3.188 0.51,0.208 10 false BDR- 2.156,4.271 2.469,4.479 0.313,0.208 10 false *5
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Front Door Wire RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM2-1 (BDR+) - Body ground Ignition switch ON Below 1 V
IM2-2 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM2-1 (BDR+) - IM2-2 (BDR-) Always 1 MΩ or higher
IM2-1 (BDR+) - Body ground Always 1 MΩ or higher
IM2-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE