Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 1 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Pre-collision System

*2: w/ Blind Spot Monitor System

*3: w/ Panoramic View Monitor System

*4: w/ TOYOTA Parking Assist-sensor System

*5: w/ Grille Shutter System

*6: w/ Parking Assist Monitor System

There is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus wire

·

Short to GND in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Forward recognition camera*1

·

Millimeter wave radar sensor assembly*1

·

Blind spot monitor sensor LH*2

·

Parking assist ECU*3

·

Television camera assembly*3, *6

·

Clearance warning ECU assembly*4

·

Swing grille actuator assembly*5

·

No. 2 CAN junction connector

·

No. 8 CAN junction connector

·

No. 1 CAN junction terminal



WIRING DIAGRAM

C405877E01
0.26,1.198 2.281,1.427 2.021,0.229 10 false No. 1 CAN Junction Terminal 0.24,2.75 2.281,2.958 2.042,0.208 10 false Blind Spot Monitor Sensor LH*2 0.24,4.396 1.688,4.802 1.448,0.406 10 false Television Camera Assembly*3, *6 5.563,7.635 6.917,8.188 1.354,0.552 10 false Central Gateway ECU (Network Gateway ECU) 5.083,6.021 6.573,6.396 1.49,0.375 10 false Clearance Warning ECU Assembly*4 5.563,4.365 7.115,4.604 1.552,0.24 10 false Parking Assist ECU*3 5.625,2.76 7,3.125 1.375,0.365 10 false Millimeter Wave Radar Sensor Assembly*1 5.604,1.125 6.865,1.49 1.26,0.365 10 false Forward Recognition Camera*1 2.313,4.458 3.542,4.885 1.229,0.427 10 false No. 8 CAN Junction Connector 3.552,7.656 4.771,8.104 1.219,0.448 10 false No. 2 CAN Junction Connector 0.229,0.99 1.781,1.229 1.552,0.24 10 false N54 0.656,0.375 2.208,0.615 1.552,0.24 10 false CANH 0.646,0.813 2.198,1.052 1.552,0.24 10 false CANL 0.854,2 1.313,2.198 0.458,0.198 10 false CA1P 0.844,2.385 1.292,2.604 0.448,0.219 10 false CA1N 0.844,3.635 2.396,3.875 1.552,0.24 10 false CANH 0.854,4.031 2.406,4.271 1.552,0.24 10 false CANL 5.948,0.365 6.531,0.594 0.583,0.229 10 false CA1P 5.948,0.75 6.531,0.979 0.583,0.229 10 false CA1N 5.927,1.979 6.51,2.208 0.583,0.229 10 false CA2H 5.927,2.385 6.51,2.615 0.583,0.229 10 false CA2L 5.927,3.615 6.51,3.844 0.583,0.229 10 false CANH 5.927,4 6.51,4.229 0.583,0.229 10 false CANL 5.938,5.271 6.521,5.5 0.583,0.229 10 false R1 5.948,5.646 6.531,5.875 0.583,0.229 10 false R2 6.021,6.781 6.604,7.01 0.583,0.229 10 false CA1H 6,7.406 6.583,7.635 0.583,0.229 10 false CA1L 0.24,2.573 1.792,2.813 1.552,0.24 10 false Q1 0.24,4.198 1.792,4.438 1.552,0.24 10 false R15 5.563,4.188 7.156,4.396 1.594,0.208 10 false N25 5.635,2.573 7.156,2.781 1.521,0.208 10 false B9 5.615,0.938 7.156,1.146 1.542,0.208 10 false P8 1.344,0.271 2.938,0.479 1.594,0.208 10 false 3 5.563,7.469 7.156,7.677 1.594,0.208 10 false G72 3.542,7.479 5.135,7.688 1.594,0.208 10 false G102 2.302,4.281 3.896,4.49 1.594,0.208 10 false N53 1.354,0.677 2.948,0.885 1.594,0.208 10 false 2 1.365,1.906 1.521,2.167 0.156,0.26 10 false 2 1.375,2.302 1.521,2.5 0.146,0.198 10 false 7 1.365,3.542 1.552,3.75 0.188,0.208 10 false 4 1.354,3.938 1.51,4.188 0.156,0.25 10 false 1 2.563,3.542 2.75,3.74 0.188,0.198 10 false 3 2.563,3.927 2.823,4.125 0.26,0.198 10 false 9 2.563,2.302 4.156,2.51 1.594,0.208 10 false 8 2.563,1.906 4.156,2.115 1.594,0.208 10 false 2 2.5,0.656 4.094,0.865 1.594,0.208 10 false 10 2.552,0.26 4.146,0.469 1.594,0.208 10 false 4 3.292,0.26 4.885,0.469 1.594,0.208 10 false 1 3.313,0.677 4.906,0.885 1.594,0.208 10 false 7 3.771,0.688 5.365,0.896 1.594,0.208 10 false 13 3.823,0.271 5.417,0.479 1.594,0.208 10 false 3 4.573,0.26 6.167,0.469 1.594,0.208 10 false 6 4.573,0.667 6.167,0.875 1.594,0.208 10 false 16 4.573,1.875 6.167,2.083 1.594,0.208 10 false 2 5.74,0.271 7.146,0.479 1.406,0.208 10 false 5 5.677,0.667 7.104,0.875 1.427,0.208 10 false 11 5.729,1.896 7.156,2.104 1.427,0.208 10 false 3 5.729,2.292 7.156,2.5 1.427,0.208 10 false 2 5.667,3.906 7.094,4.115 1.427,0.208 10 false 12 5.667,3.51 7.094,3.719 1.427,0.208 10 false 11 5.688,5.146 7.115,5.354 1.427,0.208 10 false 17 5.677,5.531 7.104,5.74 1.427,0.208 10 false 18 5.708,6.781 7.135,6.99 1.427,0.208 10 false 23 5.729,7.198 7.156,7.406 1.427,0.208 10 false 8 4.542,7.188 5.969,7.396 1.427,0.208 10 false 18 4.563,6.75 5.99,6.958 1.427,0.208 10 false 8 4.563,5.552 5.99,5.76 1.427,0.208 10 false 17 4.573,5.135 6,5.344 1.427,0.208 10 false 7 4.563,3.927 5.99,4.135 1.427,0.208 10 false 15 4.594,3.51 6.021,3.719 1.427,0.208 10 false 5 4.583,2.292 6.01,2.5 1.427,0.208 10 false 12 5.073,5.833 6.667,6.042 1.594,0.208 10 false G25*7, H4*8 0.229,6.458 2.271,6.667 2.042,0.208 10 false *1: w/ Pre-collision System 0.229,6.813 2.479,7.073 2.25,0.26 10 false *2: w/ Blind Spot Monitor System 0.219,7.167 2.948,7.438 2.729,0.271 10 false *3: w/ Panoramic View Monitor System 0.229,7.51 3.188,7.74 2.958,0.229 10 false *4: w/ TOYOTA Parking Assist-sensor System 0.229,7.844 3.188,8.073 2.958,0.229 10 false *5: w/ Grille Shutter System 1.479,6 3.74,6.313 2.26,0.313 10 false Swing Grille Actuator Assembly*5 1.479,5.823 1.896,6.021 0.417,0.198 10 false A85 2.115,5.25 2.573,5.448 0.458,0.198 10 false CANP 2.104,5.656 2.563,5.854 0.458,0.198 10 false CANN 3.813,5.146 4,5.354 0.188,0.208 10 false 4 3.75,5.552 4.031,5.75 0.281,0.198 10 false 14 2.625,5.552 2.813,5.76 0.188,0.208 10 false 5 2.615,5.146 2.802,5.354 0.188,0.208 10 false 6 0.219,8.167 3.177,8.396 2.958,0.229 10 false *6: w/ Parking Assist Monitor System 0.229,8.5 2.719,8.729 2.49,0.229 10 false *7: for LHD with Manual Transaxle 2.604,8.5 5.094,8.729 2.49,0.229 10 false *8: except LHD with Manual Transaxle


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 2 CAN junction connector.

C409616C08
0.073,1.229 0.479,1.51 0.406,0.281 5.708,0.667 6.115,0.948 0.406,0.281 1.427,2.396 1.583,2.396 1.583,2.396 1.583,1.719 true 1.615,1.396 1.604,0.427 1.604,0.427 1.458,0.427 true 3.969,2.417 3.802,2.417 3.802,2.417 3.479,1.719 true 6.51,0.865 6.344,0.865 6.344,0.865 5.885,1.208 true 1.24,1.365 1.229,0.688 1.229,0.688 1,0.688 true 1.021,2.115 1.198,2.115 1.198,2.115 1.219,1.708 true 1.99,1.406 1.969,0.26 1.969,0.26 1.823,0.26 true 2.271,1.406 2.271,0.24 2.271,0.24 2.5,0.24 true 2.698,1.375 2.708,0.406 2.708,0.406 2.885,0.406 true 3.073,1.396 3.552,0.188 3.552,0.188 3.729,0.188 true 3.438,1.375 4.125,0.365 4.125,0.365 4.302,0.365 true 3.688,2.635 3.521,2.635 3.521,2.635 3.115,1.729 true 2.844,2.438 2.677,2.438 2.677,2.438 2.656,1.698 true 1.813,2.604 1.979,2.604 1.979,2.604 1.979,1.688 true 2.385,2.615 2.26,2.615 2.26,2.615 2.26,1.677 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 0.885,0.344 1.542,0.542 0.656,0.198 10 false CANH*c 0.906,2.281 1.563,2.479 0.656,0.198 10 false CANL*c 0.115,1.271 0.708,1.479 0.594,0.208 10 false G102 3.781,0.104 4.438,0.302 0.656,0.198 10 false CANH*g 4.01,2.313 4.667,2.51 0.656,0.198 10 false CANL*h 5.281,0.156 5.938,0.354 0.656,0.198 10 false *i 6.594,0.792 6.99,0.99 0.396,0.198 10 false CG 0.469,0.615 1.125,0.813 0.656,0.198 10 false CANH*b 0.5,2.031 1.156,2.229 0.656,0.198 10 false CANL*b 1.323,0.167 1.979,0.365 0.656,0.198 10 false CANH*d 1.313,2.521 1.969,2.719 0.656,0.198 10 false CANL*d 2.542,0.167 3.198,0.365 0.656,0.198 10 false CANH*e 2.938,0.344 3.594,0.542 0.656,0.198 10 false CANH*f 4.344,0.292 5,0.49 0.656,0.198 10 false CANH*h 3.708,2.542 4.365,2.74 0.656,0.198 10 false CANL*g 2.896,2.323 3.552,2.521 0.656,0.198 10 false CANL*f 2.438,2.51 3.094,2.708 0.656,0.198 10 false CANL*e 5.771,0.729 6.365,0.938 0.594,0.208 10 false G114
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Millimeter Wave Radar Sensor Assembly (w/ Pre-collision System)
*c to No. 8 CAN Junction Connector *d to Swing Grille Actuator Assembly (w/ Grille Shutter System)
*e to Parking Assist ECU (w/ Panoramic View Monitor System) *f to Forward Recognition Camera (w/ Pre-collision System)
*g to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) *h to Central Gateway ECU (Network Gateway ECU)
*i Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Pre-collision System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Panoramic View Monitor System

*4: w/ Grille Shutter System

G102-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*1
G102-12 (CANL) - G114-4 (CG)
G102-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 8 CAN junction connector
G102-13 (CANL) - G114-4 (CG)
G102-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Swing grille actuator assembly*4
G102-14 (CANL) - G114-4 (CG)
G102-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU*3
G102-15 (CANL) - G114-4 (CG)
G102-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera*1
G102-16 (CANL) - G114-4 (CG)
G102-7 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*2
G102-17 (CANL) - G114-4 (CG)
G102-8 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G102-18 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 8 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)

D

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.
C406353C55
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.719,1.552 2.646,2.115 2.646,2.115 2.479,2.115 true 2.906,0.667 2.708,0.667 2.708,0.667 2.594,1.24 true 1.615,3.156 1.052,2.74 1.052,2.74 0.885,2.74 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.99,0.594 3.417,0.781 0.427,0.188 10 false CA1L 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.063,2.031 2.51,2.24 0.448,0.208 10 false CA1H 0.573,2.667 1.188,2.865 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-23 (CA1H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-8 (CA1L) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 8 CAN JUNCTION CONNECTOR)
a.

Reconnect the G102 No. 2 CAN junction connector.


b.

Disconnect the No. 8 CAN junction connector.

C409617C11
0.146,1.333 0.552,1.615 0.406,0.281 5.5,0.698 5.906,0.979 0.406,0.281 1.51,2.104 1.667,2.104 1.667,2.104 1.667,1.677 true 2.177,1.292 2.177,0.271 2.177,0.271 2.031,0.271 true 1.74,1.281 1.74,0.521 1.74,0.521 1.594,0.521 true 2.01,2.313 2.177,2.313 2.177,2.313 2.177,1.646 true 5.615,1.219 5.188,0.844 5.188,0.844 5.042,0.844 true 0.802,1.958 0.958,1.958 0.958,1.958 1.313,1.635 true 2.552,1.344 2.552,0.208 2.552,0.208 2.729,0.208 true 2.708,2.531 2.542,2.531 2.542,2.531 2.552,1.542 true 1.292,1.323 1,0.844 1,0.844 0.854,0.844 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.052,0.438 1.708,0.635 0.656,0.198 10 false CANH*c 1,2.01 1.656,2.208 0.656,0.198 10 false CANL*c 1.521,2.229 2.177,2.427 0.656,0.198 10 false CANL*d 1.458,0.198 2.115,0.396 0.656,0.198 10 false CANH*d 0.198,1.375 0.792,1.583 0.594,0.208 10 false N53 4.74,0.781 5.396,0.979 0.656,0.198 10 false CG 0.26,0.771 0.917,0.969 0.656,0.198 10 false CANH*b 0.302,1.865 0.958,2.063 0.656,0.198 10 false CANL*b 2.792,0.135 3.448,0.333 0.656,0.198 10 false CANH*e 4.76,0.26 5.417,0.458 0.656,0.198 10 false *f 2.729,2.448 3.385,2.646 0.656,0.198 10 false CANL*e 5.542,0.75 6.135,0.958 0.594,0.208 10 false G114
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *d to Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System)
*e to No. 1 CAN Junction Terminal *f Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Blind Spot Monitor System

*2: w/ Panoramic View Monitor System

*3: w/ Parking Assist Monitor System

N53-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction connector
N53-7 (CANL) - G114-4 (CG)
N53-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor LH*1
N53-8 (CANL) - G114-4 (CG)
N53-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Television camera assembly*2, *3
N53-9 (CANL) - G114-4 (CG)
N53-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction terminal
N53-10 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 2 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU


c.
C406381C37
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 1.656,2.552 1.854,2.167 1.854,2.167 2.021,2.167 true 1.198,0.906 1.146,1.406 1.146,1.406 0.979,1.406 true 1.063,0.323 1.229,0.323 1.229,0.323 1.24,0.75 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.635,0.25 1.094,0.448 0.458,0.198 10 false CA1L 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 0.583,1.344 1.042,1.542 0.458,0.198 10 false CA1H 2.094,2.094 2.552,2.292 0.458,0.198 10 false CG 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-23 (CA1H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-8 (CA1L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR