Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Stop and Start System

*2: for CVT

There is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus lines

·

Short to GND in CAN branch lines

·

Engine stop and start ECU*1

·

Transmission control ECU*2

·

Central gateway ECU (network gateway ECU)

·

ECM

·

No. 3 CAN junction connector



WIRING DIAGRAM

C379608E04
3.115,3.438 3.729,3.635 0.615,0.198 10 false G103 3.115,3.594 4.396,4.25 1.281,0.656 10 false No. 3 CAN Junction Connector 3.125,2.958 3.74,3.156 0.615,0.198 10 false 19 3.177,2.542 3.792,2.74 0.615,0.198 10 false 9 3.115,1.229 3.729,1.427 0.615,0.198 10 false 16 3.167,0.833 3.781,1.031 0.615,0.198 10 false 6 4.094,1.208 4.708,1.406 0.615,0.198 10 false 11 4.125,0.823 4.74,1.021 0.615,0.198 10 false 1 4.094,2.958 4.708,3.156 0.615,0.198 10 false 13 4.115,2.51 4.729,2.708 0.615,0.198 10 false 3 5.875,3.385 6.49,3.583 0.615,0.198 10 false A24 6.094,3.594 7.052,3.938 0.958,0.344 10 false ECM 5.146,1.521 5.76,1.719 0.615,0.198 10 false G72 5.146,1.698 7.063,2.188 1.917,0.49 10 false Central Gateway ECU (Network Gateway ECU) 5.667,0.813 6.281,1.01 0.615,0.198 10 false 18 5.667,1.229 6.281,1.427 0.615,0.198 10 false 17 5.948,0.854 6.563,1.052 0.615,0.198 10 false CA4H 5.948,1.438 6.563,1.635 0.615,0.198 10 false CA4L 5.958,2.573 6.573,2.771 0.615,0.198 10 false CANH 5.938,3.156 6.552,3.354 0.615,0.198 10 false CANL 5.75,2.552 6.365,2.75 0.615,0.198 10 false 8 5.688,2.958 6.302,3.156 0.615,0.198 10 false 18 0.49,3.375 1.104,3.573 0.615,0.198 10 false C33 0.479,3.542 2.406,3.875 1.927,0.333 10 false Transmission Control ECU*4 0.875,2.667 1.49,2.865 0.615,0.198 10 false CANH 0.875,3.042 1.49,3.24 0.615,0.198 10 false CANL 1.354,2.531 1.969,2.729 0.615,0.198 10 false 15 1.375,2.938 1.99,3.135 0.615,0.198 10 false 16 1.375,0.833 1.99,1.031 0.615,0.198 10 false 13 1.385,1.229 2,1.427 0.615,0.198 10 false 14 0.875,0.938 1.49,1.135 0.615,0.198 10 false CANH 0.896,1.302 1.51,1.5 0.615,0.198 10 false CANL 0.396,1.667 1.583,1.875 1.188,0.208 10 false A32*1, G62*2 0.396,1.844 2.448,2.135 2.052,0.292 10 false Engine Stop and Start ECU*3 0.385,4.115 1.479,4.323 1.094,0.208 10 false *1: for LHD 0.385,4.427 1.479,4.635 1.094,0.208 10 false *2: for RHD 1.396,4.125 3.76,4.375 2.365,0.25 10 false *3: w/ Stop and Start System 1.396,4.438 3.76,4.688 2.365,0.25 10 false *4: for CVT

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C409616C10
0.146,1.333 0.552,1.615 0.406,0.281 5.74,0.688 6.146,0.969 0.406,0.281 1.625,1.417 1.625,0.656 1.625,0.656 1.479,0.656 true 1.448,2.385 1.615,2.385 1.615,2.385 1.615,1.719 true 4.031,2.115 3.865,2.115 3.865,2.115 3.865,1.688 true 0.865,1.396 0.865,0.813 0.865,0.813 0.625,0.813 true 0.646,2.229 0.865,2.229 0.865,2.229 0.854,1.698 true 2.75,1.417 2.75,0.281 2.75,0.281 2.927,0.281 true 3.865,1.365 3.865,0.708 3.865,0.708 4.042,0.708 true 2.927,2.625 2.75,2.625 2.75,2.625 2.76,1.698 true 5.844,1.208 5.51,0.927 5.51,0.927 5.365,0.927 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 0.927,2.281 1.583,2.479 0.656,0.198 10 false CANL*c 0.927,0.563 1.583,0.76 0.656,0.198 10 false CANH*c 0.198,1.375 0.792,1.583 0.594,0.208 10 false G103 4.052,2.031 4.708,2.229 0.656,0.198 10 false CANL*e 0.094,0.74 0.75,0.938 0.656,0.198 10 false CANH*b 0.146,2.156 0.802,2.354 0.656,0.198 10 false CANL*b 2.948,0.208 3.604,0.406 0.656,0.198 10 false CANH*d 4.083,0.635 4.74,0.833 0.656,0.198 10 false CANH*e 2.958,2.521 3.615,2.719 0.656,0.198 10 false CANL*d 5.073,0.844 5.573,1.042 0.5,0.198 10 false CG 5.188,0.156 5.5,0.354 0.313,0.198 10 false *f 5.792,0.74 6.385,0.948 0.594,0.208 10 false G114
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to ECM *d to Engine Stop and Start ECU (w/ Stop and Start System)
*e to Transmission Control ECU (for CVT) *f Front view of DLC3


Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Stop and Start System

*2: for CVT

G103-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G103-11 (CANL) - G114-4 (CG)
G103-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
G103-13 (CANL) - G114-4 (CG)
G103-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Engine stop and start ECU*1
G103-16 (CANL) - G114-4 (CG)
G103-9 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Transmission control ECU*2
G103-19 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (ECM CAN main wire) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the G103 No. 3 CAN junction connector.


b.
C406353C56
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.24,2.104 2.042,2.104 2.042,2.104 1.823,1.521 true 1.646,1.5 1.365,2.083 1.365,2.083 1.198,2.083 true 1.625,3.146 1.188,2.75 1.188,2.75 1.021,2.75 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.823,2.01 1.313,2.198 0.49,0.188 10 false CA4L 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.302,2.031 2.75,2.24 0.448,0.208 10 false CA4H 0.729,2.667 1.344,2.865 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-18 (CA4H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-17 (CA4L) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.
C406381C30
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 1.635,2.583 1.802,2.219 1.802,2.219 1.969,2.219 true 1.656,0.896 1.24,1.427 1.24,1.427 1.073,1.427 true 1.75,0.885 2.271,1.438 2.271,1.438 2.438,1.438 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.667,1.354 1.125,1.552 0.458,0.198 10 false CA4H 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 2.5,1.375 2.958,1.573 0.458,0.198 10 false CA4L 2.052,2.135 2.51,2.333 0.458,0.198 10 false CG 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus wire shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-18 (CA4H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-17 (CA4L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR