Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2018.10–2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Telematics System

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type

·

There is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

·

There is no resistance between terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.


·

Short to GND in CAN main bus wire

·

Short to GND in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Telephone transceiver assembly*1

·

Bus buffer ECU*2

·

Radio and display receiver assembly*3

·

No. 5 CAN junction connector



WIRING DIAGRAM

C379634E21
0.219,1.208 0.677,1.406 0.458,0.198 10 false G2 0.24,1.365 1.927,1.76 1.688,0.396 10 false Radio and Display Receiver Assembly*3 0.927,0.635 1.385,0.833 0.458,0.198 10 false CANH 0.927,1.01 1.385,1.208 0.458,0.198 10 false CANL 0.906,2.385 1.365,2.583 0.458,0.198 10 false CANP 0.906,2.781 1.365,2.979 0.458,0.198 10 false CANN 0.927,4.125 1.385,4.323 0.458,0.198 10 false CAN+ 0.906,4.51 1.365,4.708 0.458,0.198 10 false CAN- 5.104,4.781 5.563,4.979 0.458,0.198 10 false G72 5.104,4.948 7.094,5.333 1.99,0.385 10 false Central Gateway ECU (Network Gateway ECU) 0.271,3 0.729,3.198 0.458,0.198 10 false H6 0.26,3.146 1.708,3.646 1.448,0.5 10 false Telephone Transceiver Assemblyr*1 0.25,4.75 0.708,4.948 0.458,0.198 10 false G80 0.271,4.896 2.281,5.156 2.01,0.26 10 false Bus Buffer ECU*2 1.385,4.021 1.844,4.219 0.458,0.198 10 false 2 1.396,4.375 1.854,4.573 0.458,0.198 10 false 1 1.375,2.26 1.833,2.458 0.458,0.198 10 false 15 1.385,2.656 1.844,2.854 0.458,0.198 10 false 16 1.375,0.521 1.833,0.719 0.458,0.198 10 false 13 1.385,0.927 1.844,1.125 0.458,0.198 10 false 14 3.167,0.521 3.625,0.719 0.458,0.198 10 false 5 3.115,0.906 3.573,1.104 0.458,0.198 10 false 16 4.135,0.5 4.594,0.698 0.458,0.198 10 false 2 4.125,0.906 4.583,1.104 0.458,0.198 10 false 13 5.708,0.542 6.167,0.74 0.458,0.198 10 false 6 5.667,0.917 6.125,1.115 0.458,0.198 10 false 21 3.104,2.656 3.563,2.854 0.458,0.198 10 false 14 3.177,2.24 3.635,2.438 0.458,0.198 10 false 3 3.104,4.406 3.563,4.604 0.458,0.198 10 false 12 3.146,3.99 3.604,4.188 0.458,0.198 10 false 1 4.104,3.99 4.563,4.188 0.458,0.198 10 false 4 4.083,4.396 4.542,4.594 0.458,0.198 10 false 15 5.688,4.01 6.146,4.208 0.458,0.198 10 false 19 5.677,4.417 6.135,4.615 0.458,0.198 10 false 20 5.938,4 6.396,4.198 0.458,0.198 10 false CAYH 5.958,4.625 6.417,4.823 0.458,0.198 10 false CAYL 5.969,0.479 6.427,0.677 0.458,0.198 10 false CA3H 5.948,1.135 6.406,1.333 0.458,0.198 10 false CA3L 2.844,4.771 3.302,4.969 0.458,0.198 10 false G105 2.844,4.927 5.031,5.208 2.188,0.281 10 false No. 5 CAN Junction Connector 0.188,5.5 2.198,5.76 2.01,0.26 10 false *1: w/ Telematics System 2.229,5.5 4.24,5.76 2.01,0.26 10 false *2: w/ Bus Buffer ECU 3.833,5.5 6.76,5.75 2.927,0.25 10 false *3: for Radio and Display Type

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 5 CAN junction connector.

C409618C14
0.396,1.406 0.813,1.615 0.417,0.208 4.313,1.406 4.729,1.615 0.417,0.208 1.229,1.146 1.396,1.146 1.396,1.146 1.563,1.396 true 1.125,1.917 1.292,1.917 1.292,1.917 1.479,1.75 true 1.302,0.896 1.469,0.896 1.469,0.896 1.76,1.396 true 1.271,2.094 1.438,2.094 1.438,2.094 1.719,1.75 true 1.375,0.646 1.542,0.646 1.542,0.646 1.896,1.333 true 1.406,2.302 1.573,2.302 1.573,2.302 1.917,1.771 true 2.552,0.323 2.385,0.323 2.385,0.323 2.083,1.375 true 2.438,2.292 2.271,2.292 2.271,2.292 2.104,1.771 true 2.792,0.594 2.625,0.594 2.625,0.594 2.26,1.333 true 2.667,2.115 2.5,2.115 2.5,2.115 2.219,1.75 true 5.906,0.917 5.74,0.917 5.74,0.917 5.458,1.229 true 0.542,0.208 0.854,0.406 0.313,0.198 10 false *a 3.938,0.198 4.25,0.396 0.313,0.198 10 false *g 0.677,1.083 1.396,1.302 0.719,0.219 10 false CANH*b 0.656,1.76 1.375,1.979 0.719,0.219 10 false CANL*b 0.771,0.792 1.49,1.01 0.719,0.219 10 false CANH*c 0.75,2.01 1.469,2.229 0.719,0.219 10 false CANL*c 0.875,0.573 1.594,0.792 0.719,0.219 10 false CANH*d 0.896,2.229 1.615,2.417 0.719,0.188 10 false CANL*d 2.604,0.26 3.323,0.479 0.719,0.219 10 false CANH*e 2.813,0.521 3.531,0.74 0.719,0.219 10 false CANH*f 2.698,2.063 3.396,2.271 0.698,0.208 10 false CANL*f 2.5,2.229 3.198,2.438 0.698,0.208 10 false CANL*e 5.99,0.844 6.688,1.052 0.698,0.208 10 false CG 4.385,1.427 5.083,1.635 0.698,0.208 10 false G114 0.458,1.438 1.156,1.646 0.698,0.208 10 false G105
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Radio and Display Receiver Assembly (for Radio and Display Type) *d to Telephone Transceiver Assembly (w/ Telematics System)
*e to Bus Buffer ECU (w/ Bus Buffer ECU) *f to Central Gateway ECU (Network Gateway ECU)
*g Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Telematics System

*2: w/ Bus Buffer ECU

*3: for Radio and Display Type

G105-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*2
G105-12 (CANH) - G114-4 (CG)
G105-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G105-13 (CANL) - G114-4 (CG)
G105-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telephone transceiver assembly*1
G105-14 (CANL) - G114-4 (CG)
G105-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G105-15 (CANL) - G114-4 (CG)
G105-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*3
G105-16 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.

Reconnect the G105 No. 5 CAN junction connector.


b.
C406353C64
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.823,0.615 2.625,0.615 2.625,0.615 2.313,1.24 true 2.406,2.781 2.24,2.781 2.24,2.781 1.604,3.167 true 2.583,2.115 2.385,2.115 2.385,2.115 2.177,1.521 true 2.521,2.323 2.323,2.323 2.323,2.323 2.052,1.542 true 1.906,1.521 1.573,2.302 1.573,2.302 1.406,2.302 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.667,2.042 3.156,2.229 0.49,0.188 10 false CA3L 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.938,0.531 3.385,0.74 0.448,0.208 10 false CA3H 2.51,2.708 3.125,2.906 0.615,0.198 10 false CG 2.604,2.271 3.094,2.458 0.49,0.188 10 false CAYL 1,2.208 1.49,2.396 0.49,0.188 10 false CAYH
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-6 (CA3H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-21 (CA3L) - G114-4 (CG)
G72-19 (CAYH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-20 (CAYL) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.
C406381C33
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 1.635,2.552 1.74,2.26 1.74,2.26 1.906,2.26 true 1.396,0.875 1.24,1.427 1.24,1.427 1.073,1.427 true 1.104,0.323 1.271,0.323 1.271,0.323 1.406,0.771 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.698,0.25 1.156,0.448 0.458,0.198 10 false CA3H 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 0.698,1.344 1.156,1.542 0.458,0.198 10 false CA3L 2,2.177 2.458,2.375 0.458,0.198 10 false CG 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus wire shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-6 (CA3H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-21 (CA3L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR