Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 4 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3

Symptom Trouble Area

*1: w/ Occupant Classification System

*2: for 4WD/AWD

There is no resistance between terminal 22 (CA2H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 7 (CA2L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus wire

·

Short to GND in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

Steering sensor

·

Occupant detection ECU*1

·

Rack and pinion power steering gear assembly

·

Brake actuator assembly (skid control ECU)

·

4WD ECU assembly*2

·

Airbag sensor assembly

·

No. 1 CAN junction connector

·

No. 4 CAN junction connector

·

No. 6 CAN junction terminal



WIRING DIAGRAM

C405882E02
0.083,0.927 1,1.125 0.917,0.198 10 false G72 0.083,1.063 2.021,1.479 1.938,0.417 10 false Central Gateway ECU (Network Gateway ECU) 0.844,0.26 1.302,0.469 0.458,0.208 10 false CA2H 0.865,0.865 1.323,1.073 0.458,0.208 10 false CA2L 1.354,0.25 1.604,0.448 0.25,0.198 10 false 22 1.354,0.635 1.604,0.833 0.25,0.198 10 false 7 2.292,0.635 2.542,0.833 0.25,0.198 10 false 9 2.292,0.25 2.542,0.448 0.25,0.198 10 false 3 2.083,2.875 2.396,3.073 0.313,0.198 10 false M31 2.094,3.052 3.313,3.417 1.219,0.365 10 false No. 6 CAN Junction Connector 0.25,2.865 0.563,3.063 0.313,0.198 10 false S21 0.24,3.031 1.469,3.417 1.229,0.385 10 false Occupant Detection ECU*1 0.875,2.302 1.333,2.51 0.458,0.208 10 false CANH 0.875,2.698 1.333,2.906 0.458,0.208 10 false CANL 1.354,2.594 1.604,2.792 0.25,0.198 10 false 4 1.354,2.198 1.604,2.396 0.25,0.198 10 false 5 2.281,2.583 2.531,2.781 0.25,0.198 10 false 8 2.281,2.188 2.531,2.385 0.25,0.198 10 false 2 2.948,2.583 3.198,2.781 0.25,0.198 10 false 10 2.979,2.177 3.229,2.375 0.25,0.198 10 false 4 4.229,2.594 4.531,2.792 0.302,0.198 10 false 21 4.219,2.188 4.51,2.396 0.292,0.208 10 false 10 4.969,0.625 5.219,0.823 0.25,0.198 10 false 22 4.969,0.24 5.219,0.438 0.25,0.198 10 false 11 5.542,0.906 5.854,1.104 0.313,0.198 10 false G68 5.563,1.104 6.823,1.51 1.26,0.406 10 false Steering Sensor 5.938,0.74 6.427,0.938 0.49,0.198 10 false CANL 5.917,0.333 6.406,0.531 0.49,0.198 10 false CANH 5.719,0.229 5.969,0.427 0.25,0.198 10 false 3 5.719,0.635 5.969,0.833 0.25,0.198 10 false 8 4.115,2.865 4.521,3.073 0.406,0.208 10 false G96 4.125,3.052 5.365,3.385 1.24,0.333 10 false No. 1 CAN Junction Connector 5,2.563 5.313,2.76 0.313,0.198 10 false 20 5.01,2.177 5.323,2.375 0.313,0.198 10 false 9 0.104,7.625 3.594,7.917 3.49,0.292 10 false *2: for Dynamic Torque Control 4WD/AWD System 4.552,4.073 4.865,4.271 0.313,0.198 10 false 4 4.531,4.479 4.844,4.677 0.313,0.198 10 false 10 3.823,4.479 4.135,4.677 0.313,0.198 10 false 11 3.875,4.073 4.188,4.271 0.313,0.198 10 false 5 2.448,4.021 2.76,4.219 0.313,0.198 10 false 10 3.865,5.708 4.177,5.906 0.313,0.198 10 false 1 1.948,4.167 2.438,4.365 0.49,0.198 10 false CANH 1.948,4.563 2.438,4.76 0.49,0.198 10 false CANL 1.302,4.708 1.792,4.906 0.49,0.198 10 false C54 1.313,4.906 3.073,5.333 1.76,0.427 10 false Rack and Pinion Power Steering Gear Assembly 5.656,6.615 7.156,6.969 1.5,0.354 10 false 4WD ECU Assembly*4 5.969,5.844 6.458,6.042 0.49,0.198 10 false CANH 5.969,6.229 6.458,6.427 0.49,0.198 10 false CANL 4.542,5.708 4.854,5.906 0.313,0.198 10 false 3 4.542,6.135 4.854,6.333 0.313,0.198 10 false 9 4.542,7.333 4.896,7.531 0.354,0.198 10 false 2 4.552,7.75 4.865,7.948 0.313,0.198 10 false 8 6.052,7.333 6.542,7.531 0.49,0.198 10 false CANH 6.063,7.938 6.552,8.135 0.49,0.198 10 false CANL 5.469,8.031 5.958,8.229 0.49,0.198 10 false G70 5.479,8.219 7.115,8.646 1.635,0.427 10 false Airbag Sensor Assembly 3.583,7.917 4.073,8.115 0.49,0.198 10 false G104 3.615,8.104 4.865,8.531 1.25,0.427 10 false No. 4 CAN Junction Connector 0.115,8.021 3.552,8.323 3.438,0.302 10 false *3: for Dynamic Torque Vectoring AWD System 5.729,7.344 6.031,7.563 0.302,0.219 10 false 26 5.729,7.75 6.01,7.948 0.281,0.198 10 false 27 1.344,6.594 2.927,6.979 1.583,0.385 10 false Brake Actuator Assembly (Skid Control ECU) 1.344,6.427 1.833,6.625 0.49,0.198 10 false A39 1.948,5.833 2.438,6.031 0.49,0.198 10 false CANH 1.969,6.219 2.458,6.417 0.49,0.198 10 false CANL 2.458,6.115 2.771,6.313 0.313,0.198 10 false 19 3.875,6.125 4.188,6.323 0.313,0.198 10 false 7 5.271,5.813 5.76,6.01 0.49,0.198 10 false N4 5.646,6.219 6.135,6.417 0.49,0.198 10 false N5 5.635,5.823 6.125,6.021 0.49,0.198 10 false N5 5.281,6.219 5.771,6.417 0.49,0.198 10 false N4 5.208,5.625 5.698,5.823 0.49,0.198 10 false 17*2 5.208,6.031 5.698,6.229 0.49,0.198 10 false 26*2 5.625,5.625 6.115,5.823 0.49,0.198 10 false 6*3 5.625,6.042 6.115,6.24 0.49,0.198 10 false 5*3 0.104,7.229 2.854,7.5 2.75,0.271 10 false *1: w/ Occupant Classification System 2.448,5.698 2.771,5.896 0.323,0.198 10 false 5 2.448,4.427 2.802,4.625 0.354,0.198 10 false 11 0.104,8.438 3.542,8.74 3.438,0.302 10 false *4: for 4WD/AWD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.

C409618C11
0.396,1.208 0.823,1.469 0.427,0.26 4.063,1.313 4.49,1.573 0.427,0.26 2.906,1.406 2.677,0.552 2.677,0.552 2.427,0.552 true 2.906,1.75 2.719,2.25 2.719,2.25 2.469,2.25 true 3.104,1.448 2.958,0.354 2.958,0.354 2.708,0.354 true 3.073,1.698 2.917,2.448 2.917,2.448 2.667,2.448 true 3.219,1.688 3.25,2.5 3.25,2.5 3.417,2.5 true 3.302,1.417 3.438,0.833 3.438,0.833 3.604,0.833 true 5.458,1.229 5.417,0.917 5.417,0.917 5.25,0.917 true 0.604,0.208 0.917,0.406 0.313,0.198 10 false *a 3.906,0.188 4.219,0.385 0.313,0.198 10 false *e 1.865,0.469 2.479,0.667 0.615,0.198 10 false CANH*b 0.479,1.271 1.094,1.469 0.615,0.198 10 false G96 4.115,1.354 4.729,1.552 0.615,0.198 10 false G114 1.917,2.156 2.531,2.354 0.615,0.198 10 false CANL*b 2.156,0.26 2.771,0.458 0.615,0.198 10 false CANH*c 2.156,2.365 2.771,2.563 0.615,0.198 10 false CANL*c 3.677,0.76 4.292,0.958 0.615,0.198 10 false CANH*d 3.469,2.427 4.083,2.625 0.615,0.198 10 false CANL*d 4.927,0.854 5.542,1.052 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to No. 6 CAN Junction Connector *d to Steering Sensor
*e Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G96-9 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 4 CAN junction connector
G96-20 (CANL) - G114-4 (CG)
G96-10 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 6 CAN junction connector
G96-21 (CANL) - G114-4 (CG)
G96-11 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
G96-22 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)

C

4.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)

D

5.CHECK SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
2.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 6 CAN junction connector.

C409617C15
0.365,1.271 0.771,1.5 0.406,0.229 5.406,0.698 5.875,0.948 0.469,0.25 0.729,0.656 0.896,0.656 0.896,0.656 1.677,1.344 true 0.813,2.083 0.979,2.083 0.979,2.083 1.708,1.594 true 1.469,0.458 1.635,0.458 1.635,0.458 2.146,1.354 true 1.385,2.438 1.552,2.438 1.552,2.438 2.146,1.604 true 3.729,0.271 3.479,0.271 3.479,0.271 2.604,1.333 true 3.375,2.448 3.125,2.448 3.125,2.448 2.594,1.625 true 5.042,0.958 5.208,0.958 5.208,0.958 5.615,1.229 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false M31 0.156,0.594 0.708,0.771 0.552,0.177 10 false CANH*b 0.26,2 0.813,2.177 0.552,0.177 10 false CANL*b 0.885,0.385 1.438,0.563 0.552,0.177 10 false CANH*c 0.865,2.354 1.417,2.531 0.552,0.177 10 false CANL*c 3.792,0.198 4.344,0.375 0.552,0.177 10 false CANH*d 3.438,2.385 3.99,2.563 0.552,0.177 10 false CANL*d 5.469,0.75 5.927,0.969 0.458,0.219 10 false G114 4.76,0.865 5.177,1.052 0.417,0.188 10 false CG 4.719,0.458 5.031,0.656 0.313,0.198 10 false *e
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Occupant Detection ECU (w/ Occupant Classification System)
*c to Central Gateway ECU (Network Gateway ECU) *d to No. 1 CAN Junction Connector
*e Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*: w/ Occupant Classification System

M31-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Occupant detection ECU*
M31-8 (CANL) - G114-4 (CG)
M31-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
M31-9 (CANL) - G114-4 (CG)
M31-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
M31-10 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

3.CHECK SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
3.CHECK SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the M31 No. 6 CAN junction connector.


b.
C406353C58
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.729,2.104 2.531,2.104 2.531,2.104 2.313,1.521 true 1.646,3.146 1.25,2.75 1.25,2.75 1.083,2.75 true 2.75,0.667 2.552,0.667 2.552,0.667 2.417,1.24 true 1.563,0.292 2.177,0.49 0.615,0.198 10 false G72 1.5,2.573 2.115,2.771 0.615,0.198 10 false G114 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 2.813,0.594 3.302,0.781 0.49,0.188 10 false CA2L 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.792,2.031 3.24,2.24 0.448,0.208 10 false CA2H 0.771,2.688 1.385,2.885 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-22 (CA2H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-7 (CA2L) - G114-4 (CG)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

4.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the G96 No. 1 CAN junction connector.


b.

Disconnect the No. 4 CAN junction connector.

C409617C16
0.365,1.271 0.771,1.5 0.406,0.229 5.406,0.698 5.875,0.948 0.469,0.25 0.729,0.656 0.896,0.656 0.896,0.656 1.677,1.344 true 0.813,2.083 0.979,2.083 0.979,2.083 1.708,1.594 true 1.469,0.458 1.635,0.458 1.635,0.458 2.146,1.354 true 1.385,2.438 1.552,2.438 1.552,2.438 2.146,1.604 true 3.729,0.271 3.479,0.271 3.479,0.271 2.604,1.333 true 3.375,2.448 3.125,2.448 3.125,2.448 2.594,1.625 true 4.146,0.51 3.896,0.51 3.896,0.51 3.031,1.385 true 3.792,2.135 3.542,2.135 3.542,2.135 3.052,1.604 true 0.729,0.948 0.896,0.948 0.896,0.948 1.25,1.354 true 0.771,1.875 0.938,1.875 0.938,1.875 1.24,1.594 true 5.135,0.906 5.302,0.906 5.302,0.906 5.583,1.219 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.417,1.313 0.781,1.469 0.365,0.156 10 false G104 0.156,0.594 0.708,0.771 0.552,0.177 10 false CANH*c 0.26,2 0.813,2.177 0.552,0.177 10 false CANL*c 0.885,0.385 1.438,0.563 0.552,0.177 10 false CANH*d 0.865,2.354 1.417,2.531 0.552,0.177 10 false CANL*d 3.792,0.198 4.344,0.375 0.552,0.177 10 false CANH*e 3.438,2.385 3.99,2.563 0.552,0.177 10 false CANL*e 5.469,0.75 5.927,0.969 0.458,0.219 10 false G114 4.865,0.823 5.281,1.01 0.417,0.188 10 false CG 4.917,0.427 5.229,0.625 0.313,0.198 10 false *g 4.188,0.438 4.74,0.615 0.552,0.177 10 false CANH*f 3.865,2.063 4.417,2.24 0.552,0.177 10 false CANL*f 0.146,0.885 0.698,1.063 0.552,0.177 10 false CANH*b 0.219,1.802 0.771,1.979 0.552,0.177 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Brake Actuator Assembly (Skid Control ECU)
*c to Airbag Sensor Assembly *d to 4WD ECU Assembly (for 4WD/AWD)
*e to No. 1 CAN Junction Connector *f to Rack and Pinion Power Steering Gear Assembly
*g Front view of DLC3 - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*: for 4WD/AWD

G104-1 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)
G104-7 (CANL) - G114-4 (CG)
G104-2 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
G104-8 (CANL) - G114-4 (CG)
G104-3 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU assembly*
G104-9 (CANL) - G114-4 (CG)
G104-4 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
G104-10 (CANL) - G114-4 (CG)
G104-5 (CANH) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rack and pinion power steering gear assembly
G104-11 (CANL) - G114-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
5.CHECK SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.
C406381C40
1.5,0.083 1.917,0.333 0.417,0.25 0.417,2.583 0.833,2.833 0.417,0.25 1.323,0.896 1.24,1.427 1.24,1.427 1.073,1.427 true 1.104,0.323 1.271,0.323 1.271,0.323 1.323,0.781 true 1.052,2.198 1.219,2.198 1.219,2.198 1.635,2.563 true 0.469,2.625 0.927,2.823 0.458,0.198 10 false G114 0.729,0.25 1.188,0.448 0.458,0.198 10 false CA2L 1.583,0.135 2.042,0.333 0.458,0.198 10 false G72 0.677,1.344 1.135,1.542 0.458,0.198 10 false CA2H 0.76,2.135 1.219,2.333 0.458,0.198 10 false CG 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a 0.135,2.115 0.594,2.313 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G72-22 (CA2H) - G114-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G72-7 (CA2L) - G114-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPAIR ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR