Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM (for HV Model)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0379921 OCCUPANT CLASSIFICATION SYSTEM(for HV Model) C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM(for HV Model)  B1787  Rear Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1787 is stored when the occupant detection ECU receives a collision detection signal sent by the rear occupant classification sensor LH in the case of an accident.

DTC B1787 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident did not occur.

If the vehicle was not in a collision, but the occupant detection ECU receives a collision detection signal and stores DTC B1787, the DTC can be cleared by performing zero point calibration.

Therefore, if DTC B1787 is output, first perform zero point calibration.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1787 Rear Occupant Classification Sensor LH Collision Detection
·

Rear occupant classification sensor LH sensed large load.

·

Front seat adjuster assembly RH malfunction


Front seat adjuster assembly RH (Rear occupant classification sensor LH)*

*: The rear occupant classification sensor LH is built into the front seat adjuster assembly RH.


CAUTION / NOTICE / HINT

CAUTION:

When this DTC is stored, repair of the malfunction indicated can only be performed by initializing the occupant detection ECU or replacing the front seat adjuster assembly RH. Do not replace the occupant detection ECU to repair the malfunction indicated by this DTC.

If the occupant detection ECU is replaced, this DTC will not be output but the occupant detection system may not function properly.


NOTICE:

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:

When DTC B165A is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1787 is output, perform troubleshooting for this DTC first.


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435
OK:

"Zero Point Calibration is complete." is displayed.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC

NG

3.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
2.CHECK DTC
a.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

b.

Clear the DTCs stored in the airbag sensor assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the power switch off.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Check the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
Result:
Proceed to
DTC B1785 is output.
DTC B1785 is not output.


HINT:

Codes other than DTC B1785 may be output at this time, but they are not related to this check.




DTC B1785 is output.

3.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH

DTC B1785 is not output.

END (NORMAL AFTER PERFORMING ZERO POINT CALIBRATION)

3.REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat adjuster assembly RH with a new one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

4.PERFORM ZERO POINT CALIBRATION
4.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform "Zero Point Calibration".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM (for HV Model)>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END (FRONT SEAT ADJUSTER ASSEMBLY RH WAS DEFECTIVE)