Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
87501A
1.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System, w/ Climate Control Seat System)
89952
2.REMOVE OCCUPANT DETECTION ECU (for Front Passenger Side, w/ Occupant Classification System)
73240
3.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
73230
4.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
72495
5.REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)
|
Lift in this Direction |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the vertical adjusting handle LH while lifting it up.
Tape the thin-bladed screwdriver tip before use.
72552B
6.REMOVE RECLINING HINGE COVER LH
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide to remove the reclining hinge cover LH as shown in the illustration.
72526A
7.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Detach the guide to remove the reclining adjuster release handle LH.
71849
8.REMOVE SEAT ADJUSTER COVER CAP LH (for Driver Side)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using moulding remover A, detach the claw in the removal direction (1) shown in the illustration.
Pull in the removal direction (2) shown in the illustration and detach the guide to remove the seat adjuster cover cap LH.
71812D
9.REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the guide and remove the front seat cushion shield LH.
71811D
10.REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the guide and remove the front seat cushion shield RH.
71862
11.REMOVE FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and remove the front seat inner cushion shield LH.
71861
12.REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
|
Remove in this Direction |
Using moulding remover A, detach the claw and guide.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and remove the front seat inner cushion shield RH.
72498A
13.REMOVE VERTICAL ADJUSTER BRACKET COVER LH (for Driver Side)
Detach the claw and guide to remove the vertical adjuster bracket cover LH.
14.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Detach the band.
Detach the hook.
w/ Climate Control Seat System:
Disconnect the connector.
Detach the clamp.
w/ Seat Heater System:
Disconnect the connector.
Detach the clamp.
Detach the clamp and claw.
Remove the 4 bolts.
|
Protective Tape |
Using a screwdriver, detach the guide to remove the separate type front seatback assembly.
Tape the screwdriver tip before use.
15.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Detach the hook.
w/ Seat Heater System:
Detach the clamp.
Open the 2 fasteners.
|
Remove in this Direction |
Detach the claw to remove the 2 front seat headrest supports as shown in the illustration.
Remove the separate type front seatback cover with pad.
71074S
16.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
for Standard Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seatback cover.
Tape the thin-bladed screwdriver tip before use.
for Sports Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seatback cover.
Tape the thin-bladed screwdriver tip before use.
87510N
17.REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
87510M
18.REMOVE FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
73920A
19.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH
8219A
20.REMOVE FRONT NO. 2 SEAT WIRE RH (w/ Climate Control Seat System, for LHD)
Disconnect the connector.
Detach the clamp to remove the front No. 2 seat wire RH.
8219B
21.REMOVE FRONT NO. 2 SEAT WIRE LH (w/ Climate Control Seat System, for RHD)
Disconnect the connector.
Detach the clamp to remove the front No. 2 seat wire LH.
71054S
22.REMOVE FRONT SEATBACK SPRING SUB-ASSEMBLY LH
|
Remove in this Direction |
Detach the clamp.
Pull in the removal direction shown in the illustration to remove the front seatback spring sub-assembly LH.
Remove the 2 front seatback edge protectors together with the front seatback spring sub-assembly LH.
w/ Climate Control Seat System:
|
Remove in this Direction |
Remove the front seatback felt RH.
71587B
23.REMOVE FRONT SEATBACK EDGE PROTECTOR
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the 2 front seatback edge protectors.
Tape the thin-bladed screwdriver tip before use.
71759D
24.REMOVE FRONT NO. 2 SEATBACK HOOK
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the 2 front No. 2 seatback hooks.
Do not reuse the removed front No. 2 seatback hook.
Tape the thin-bladed screwdriver tip before use.
25.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
w/o Climate Control Seat System, w/ Seat Heater System:
Detach the claw and clamp.
w/ Climate Control Seat System, w/ Seat Heater System:
Disconnect the connector.
Detach the clamp.
|
Protective Tape |
for Front Passenger Side, w/o Occupant Classification System:
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Detach the hook.
Detach the hook to remove the separate type front seat cushion cover with pad.
71072S
26.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
| *a | Band |
|
Remove in this Direction |
Detach the band.
for Standard Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seat cushion cover.
Tape the thin-bladed screwdriver tip before use.
for Sports Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seat cushion cover.
Tape the thin-bladed screwdriver tip before use.
87510L
27.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
87510K
28.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
739F0
29.REMOVE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (for Front Passenger Side, w/ Occupant Classification System)
82667D
30.REMOVE CONNECTOR HOLDER (for Front Passenger Side, w/o Occupant Classification System)
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the connector holder.
Tape the thin-bladed screwdriver tip before use.
71876G
31.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER (for Driver Side)
|
Remove in this Direction |
Detach the claw and hook to remove the LH seat reclining adjuster inside cover as shown in the illustration.
71876F
32.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER (for Front Passenger Side)
| *a | Clamp |
| *b | Hook |
|
Remove in this Direction |
w/ Occupant Classification System:
Detach the clamp.
Detach the claw and hook to remove the RH seat reclining adjuster inside cover as shown in the illustration.
71875G
33.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER (for Driver Side)
|
Remove in this Direction |
Detach the claw and hook to remove the LH seat reclining adjuster inside cover as shown in the illustration.
71875F
34.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER (for Front Passenger Side)
|
Protective Tape |
w/ Climate Control Seat System:
Detach the clamp.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
|
Remove in this Direction |
Detach the claw and hook to remove the RH seat reclining adjuster inside cover as shown in the illustration.
71874A
35.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
| *a | Hook |
| *b | Guide |
|
Remove in this Direction |
|
Protective Tape |
Detach the hook.
Using a thin-bladed screwdriver, detach the claw as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front seat lower cushion shield LH.
71873U
36.REMOVE FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
| *a | Hook |
| *b | Guide |
|
Remove in this Direction |
|
Protective Tape |
Detach the hook.
Using a thin-bladed screwdriver, detach the claw as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front seat lower cushion shield RH.
85860A
37.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH (w/ Climate Control Seat System)
Disconnect the connector.
Remove the 2 bolts.
Detach the hook to remove the seat cushion climate control blower assembly RH.
82191
38.REMOVE FRONT SEAT WIRE RH (w/ Climate Control Seat System)
| *a | w/ Seat Heater System |
Detach the clamp.
Detach the claw to remove the front seat wire RH.
7181B
39.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER LH
for Front Passenger Side, w/ Occupant Classification System:
Disconnect the 2 connectors.
Remove the 2 screws.
Detach the guide to remove the front seat cushion wire harness holder LH.
82191A
40.REMOVE FRONT SEAT WIRE RH (for Front Passenger Side, w/ Occupant Classification System)
Detach the clamp.
Detach the claw to remove the front seat wire RH.
41.REMOVE CONNECTOR MALE HOUSING (w/ Dummy Connector)
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the connector male housing.
Tape the thin-bladed screwdriver tip before use.
71052A
42.REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
| *a | Hook A |
| *b | Hook B |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration to detach the hook A.
Pull in the removal direction (2) shown in the illustration to detach the hook B and remove the front seat cushion spring sub-assembly LH.
72211C
43.REMOVE SEAT TRACK ADJUSTING HANDLE
|
Protective Tape |
Using a screwdriver, detach the claw to remove the seat track adjusting handle.
Tape the screwdriver tip before use.
72266
44.REMOVE SEAT UPPER TRACK RAIL COVER LH
Use the same procedure for both sides.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the seat upper track rail cover LH.
Tape the thin-bladed screwdriver tip before use.
72125T
45.REMOVE FRONT SEAT REAR UPPER TRACK COVER LH
Use the same procedure for both sides.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the front seat rear upper track cover LH.
Tape the thin-bladed screwdriver tip before use.
72443B
46.REMOVE VERTICAL ADJUSTER GEAR LH (for Driver Side)
Remove the vertical adjuster gear LH.
Remove the 3 nuts and vertical adjuster plate.
Remove the vertical adjuster spacer.
Remove the front vertical adjuster brake sub-assembly LH.