This DTC is stored when the engine coolant temperature does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P012800 | Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) | All of the following conditions are met for 5 seconds or more (2 trip detection logic):
1.
Cold start. 2.
The engine is warmed up. 3.
The engine coolant temperature is less than 75°C (167°F). |
·
Water inlet with thermostat sub-assembly ·
Engine cooling system ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0128 |
| P012807 | Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Mechanical Failure | All of the following conditions are met for 3 times (2 trip detection logic):
1.
The engine coolant temperature is less than 75°C (167°F). 2.
The value of the change in engine coolant temperature is less than the threshold. |
·
Water inlet with thermostat sub-assembly (thermostat) ·
Engine cooling system ·
Engine coolant temperature sensor ·
Flow Shutting Valve (for Heater Control) ·
Flow Shutting Valve (for ATF Control) ·
ATF temperature sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0128 |
The ECM estimates the engine coolant temperature based on the starting temperature, engine load, and engine speed. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction of the thermostat or in the engine cooling system, illuminate the MIL and stores this DTC.
When the vehicle is being driven between 65 and 128 km/h (40.625 and 80 mph) and the monitoring conditions are met, the change in engine coolant temperature is monitored. The amount of change is judged to be normal or abnormal every 13 seconds, in order to monitor the thermostat operation. If the engine coolant temperature changes more than the threshold, the thermostat is judged as normal, but if it changes less than the threshold, the thermostat is judged to be malfunctioning. If an abnormal judgement is made 3 times, the ECM will illuminate the MIL and store a DTC.
| Frequency of Operation | Once per driving cycle |
Stop the engine and allow it to soak.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) [A].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Intake Air Temperature.
Check that the value of the Data List item Coolant Temperature is 56°C (133°F) or less and the value of the Data List item Intake Air Temperature is between 0 and 35°C (32 and 95°F).
Set the heater control to MAX HOT with fresh air mode selected and turn the A/C off.
Start the engine and drive the vehicle at 80 km/h (50 mph) or more for 20 minutes [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After the value of the Data List item Coolant Temperature stabilizes, check that it is 75°C (167°F) or higher.
If the value of the Data List item Coolant Temperature is less than 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P012800 or P012807.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, If the judgment result is INCOMPLETE, perform steps [D] through [G].
With the engine stopped, leave the vehicle outside overnight [D].
Turn the engine switch on (IG) [E].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Check that the value of the Data List item Coolant Temperature is 25°C (77°F) or less.
Start the engine and drive the vehicle at 90 km/h (56 mph) or more for 20 minutes [F].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [G].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P012800 or P012807.
Check the DTC judgment result again.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
When this DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature. If the value of Coolant Temperature is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and their connection condition) between the ECM and the engine coolant temperature sensor first.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P012800 is output | A |
| DTC P012807 is output | B |
| DTC P012800, P012807 and other DTCs are output | C |
If any DTCs other than P012800 or P012807 are output, troubleshoot those DTCs first.
A
B
C
Check for defects in the engine cooling system that might cause the system to be too cold, such as abnormal cooling fan operation or any modifications.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).
Click hereEngine / Hybrid System>A25A-FKS (COOLING)>THERMOSTAT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Check for DTCs.
If DTCs related to the ATF temperature are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
A
B
Cool the engine.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Coolant Water Route Switching Valve / DataList / Engine Speed and Coolant Water Route Switching Valve.
| Active Test Display |
|---|
| Activate the Coolant Water Route Switching Valve |
| Data List Display |
|---|
| Engine Speed |
| Coolant Water Route Switching Valve |
Perform the Active Test to close the flow shutting valve (for Heater Control).
Start the engine.
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 1500 rpm for 15 seconds.
During the engine warm-up process, touch the flow shutting valve (for Heater Control) outlet and inlet hoses and check if there is a difference in temperature.
There is a difference in temperature.
P012807 may also be output if the flow shutting valve (for Heater Control) cannot fully close while the engine is cool.
If the flow shutting valve (for Heater Control) is closed during the engine warm-up process, there will be a difference in temperature between the outlet and inlet hoses.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Cool the engine.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Coolant Water Route Switching Valve / DataList / Engine Speed and Coolant Water Route Switching Valve 2.
| Active Test Display |
|---|
| Activate the Coolant Water Route Switching Valve 2 |
| Data List Display |
|---|
| Engine Speed |
| Coolant Water Route Switching Valve 2 |
Perform the Active Test to close the flow shutting valve (for ATF Control).
Start the engine.
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 1500 rpm for 15 seconds.
During the engine warm-up process, touch the flow shutting valve (for ATF Control) outlet and inlet hoses and check if there is a difference in temperature.
There is a difference in temperature.
P012807 may also be output if the flow shutting valve (for ATF Control) cannot fully close while the engine is cool.
If the flow shutting valve (for ATF Control) is closed during the engine warm-up process, there will be a difference in temperature between the outlet and inlet hoses.
| Proceed to |
|---|
| OK |
| NG |
OK
NG