Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076382 A25A-FKS ENGINE CONTROL _0379392 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P05042B  Brake Switch "A"/"B" Signal Cross Coupled  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).


On the GTS, Data List item Stop Light SW is ON when the brake pedal is depressed.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05042B Brake Switch "A"/"B" Signal Cross Coupled Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

Instrument panel junction block assembly

·

ECM


Does not come on DTC stored SAE Code: P0504

WIRING DIAGRAM

A436769E01
0.51,3.969 1.583,4.167 1.073,0.198 10 false Battery 0.427,2.958 1.5,3.156 1.073,0.198 10 false J/B-B 4.302,2.083 5.438,2.438 1.135,0.354 10 false Stop Light Switch Assembly 4.281,1.917 5.417,2.271 1.135,0.354 10 false A40 1.792,4.073 4.865,4.344 3.073,0.271 10 false Certification ECU (Smart Key ECU Assembly) 1.792,3.917 4.865,4.188 3.073,0.271 10 false G54 2.49,3.563 5.563,3.833 3.073,0.271 10 false IG1D 1.521,1.76 2.656,2.115 1.135,0.354 10 false IG2-NO. 2 2.875,3.448 4.01,3.802 1.135,0.354 10 false 17 1.24,2.042 3.229,2.417 1.99,0.375 10 false Instrument Panel Junction Block Assembly 2.344,0.76 3.479,1.115 1.135,0.354 10 false STOP 2.156,1.229 3.292,1.583 1.135,0.354 10 false ECU-IG2 NO. 3 0.927,0.625 2,0.823 1.073,0.198 10 false 4L 0.927,1.51 2,1.708 1.073,0.198 10 false 4D 3.177,1.51 4.25,1.708 1.073,0.198 10 false 4A 3.188,1.083 4.26,1.281 1.073,0.198 10 false 4F 3.177,0.625 4.25,0.823 1.073,0.198 10 false 4F 0.948,0.458 2.021,0.656 1.073,0.198 10 false 1 0.958,1.333 2.031,1.531 1.073,0.198 10 false 3 3.229,0.458 4.302,0.656 1.073,0.198 10 false 3 3.188,0.917 4.26,1.115 1.073,0.198 10 false 15 3.188,1.333 4.26,1.531 1.073,0.198 10 false 17 4.448,1.417 5.521,1.615 1.073,0.198 10 false GND 4.458,1.104 5.531,1.302 1.073,0.198 10 false B 4.458,0.635 5.531,0.833 1.073,0.198 10 false B 5.125,0.625 6.198,0.823 1.073,0.198 10 false L 5.135,1.417 6.208,1.615 1.073,0.198 10 false L 5.323,1.333 6.396,1.531 1.073,0.198 10 false 5 5.333,0.49 6.406,0.688 1.073,0.198 10 false 3 4.271,0.5 5.344,0.698 1.073,0.198 10 false 7 4.271,0.969 5.344,1.167 1.073,0.198 10 false 6 4.271,1.302 5.344,1.5 1.073,0.198 10 false 2 5.688,0.51 6.76,0.708 1.073,0.198 10 false 21 5.677,1.323 6.75,1.521 1.073,0.198 10 false 22 5.948,0.521 7.021,0.719 1.073,0.198 10 false STP 5.948,1.333 7.021,1.531 1.073,0.198 10 false ST1- 6.427,4.427 6.917,4.708 0.49,0.281 10 false ECM 6.042,4.427 6.531,4.708 0.49,0.281 10 false A24

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light SW
Depressed ON
Released OFF


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A418954C25
0.302,0.938 0.719,1.167 0.417,0.229 2.635,1.708 2.219,1.323 false 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 2.677,1.677 2.833,1.875 0.156,0.198 10 false B 0.385,0.969 0.844,1.167 0.458,0.198 10 false A40
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A418954C26
0.344,0.938 0.76,1.188 0.417,0.25 2.344,1.833 2.063,1.344 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.438,0.969 0.896,1.167 0.458,0.198 10 false A40 2.344,1.854 2.802,2.052 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-6 (B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
A403288C01
4.396,0.802 4.813,1.094 0.417,0.292 6.406,1.49 5.427,0.781 true 4.594,1.469 5.375,0.792 true 1.219,1.427 1.531,1.625 0.313,0.198 10 false *a 2.885,1.406 3.198,1.604 0.313,0.198 10 false *b 4.417,0.073 4.729,0.271 0.313,0.198 10 false *c 4.469,0.854 4.865,1.115 0.396,0.26 10 false A24 6.302,1.521 6.917,1.719 0.615,0.198 10 false ST1- 4.458,1.49 4.917,1.688 0.458,0.198 10 false STP
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -


a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A24-22 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A24-21 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-5 (L) - A24-22 (ST1-) Always Below 1 Ω
A40-3 (L) - A24-21 (STP) Always Below 1 Ω
A40-5 (L) or A24-22 (ST1-) - Body ground and other terminals Always 10 kΩ or higher
A40-3 (L) or A24-21 (STP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-15 - A40-6 (B) Always Below 1 Ω
4F-15 or A40-6 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - G54-17 (IG1D) Always Below 1 Ω
4A-17 or G54-17 (IG1D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR