The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Do not remove the main body ECU (multiplex network body ECU) except when replacing it.
When removing the main body ECU (multiplex network body ECU), always replace it with a new one.
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
73900
6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (except Manual Transaxle)
55308B
7.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (except Manual Transaxle)
Detach the 2 wire harness clamps.
|
Nut |
|
Bolt |
Remove the nut, bolt and No. 3 instrument panel to cowl brace sub-assembly.
8.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (except Manual Transaxle)
| *a | w/ Clearance Warning System |
Detach the 2 wire harness clamps.
w/ Clearance Warning System:
Disconnect the 5 connectors.
w/o Clearance Warning System:
Disconnect the 4 connectors.
| *a | Lever Connector |
|
Rotate in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.
Detach the wire harness clamp.
Disconnect the 2 connectors.
Disconnect the 5 connectors.
Remove the 2 nuts.
Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.
Detach the claw and remove the instrument panel junction block assembly with main body ECU from the connector holder.
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.
| *a | Lever Connector | - | - |
|
Rotate in this Direction |
|
Protective Tape |
Detach the wire harness clamp and remove the instrument panel junction block assembly with main body ECU.
89221
9.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except Manual Transaxle)
Detach the claw and remove the junction block bracket from the instrument panel junction block assembly with main body ECU.
Press the lock of the instrument panel junction block assembly and release the lock of the main body ECU (multiplex network body ECU) as shown in the illustration.
| *a | Instrument Panel Junction Block Assembly | *b | Main Body ECU (Multiplex Network Body ECU) |
|
Movement Direction |
|
Instrument Panel Junction Block Assembly Lock |
While pressing the lock, horizontally insert a thin-bladed screwdriver with its tip wrapped with protective tape between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
|
Horizontally Insert a Thin-bladed Screwdriver |
|
Protective Tape |
| *a | Internal Connector |
|
Insert a Thin-bladed Screwdriver in this Direction |
|
Released in this Direction |
|
Protective Tape |
When the thin-bladed screwdriver with its tip wrapped with protective tape is inserted, the internal connector lock is released.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
Do not excessively insert the screwdriver. Otherwise, the internal connector terminals may become deformed or damaged.
Replace the instrument panel junction block assembly when the connector terminal, the locking section, or the case is damaged or deformed.
Hold the rib of the main body ECU (multiplex network body ECU).
|
Rotate in this Direction |
While rotating the main body ECU (multiplex network body ECU), completely release the lock.
|
Remove in this Direction |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
58810J
10.REMOVE CONSOLE BOX ASSEMBLY (for Manual Transaxle)
67913B
11.REMOVE FRONT DOOR SCUFF PLATE RH (for Manual Transaxle)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62111C
12.REMOVE COWL SIDE TRIM BOARD RH (for Manual Transaxle)
55607
13.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for Manual Transaxle)
55550
14.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for Manual Transaxle)
55433B
15.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)
16.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)
Disconnect the connector.
Detach the 2 wire harness clamps.
| *a | Lever Connector |
|
Rotate in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.
Disconnect the 2 connectors.
Disconnect the 3 connectors.
|
Nut |
|
Bolt |
Remove the nut, bolt and disconnect the ECU integration box RH.
|
Slide in this Direction |
Slide the ECU integration box RH in the direction indicated by the arrow shown in the illustration.
|
Nut |
|
Bolt |
Remove the nut and bolt.
Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.
Detach the 2 wire harness clamps.
|
Rotate in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw, disconnect the 2 lever connectors and remove the instrument panel junction block assembly with main body ECU.
89221
17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Manual Transaxle)
Press the lock of the instrument panel junction block assembly and release the lock of the main body ECU (multiplex network body ECU) as shown in the illustration.
| *a | Instrument Panel Junction Block Assembly | *b | Main Body ECU (Multiplex Network Body ECU) |
|
Movement Direction |
|
Instrument Panel Junction Block Assembly Lock |
While pressing the lock, horizontally insert a thin-bladed screwdriver with its tip wrapped with protective tape between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
|
Horizontally Insert a Thin-bladed Screwdriver |
|
Protective Tape |
| *a | Internal Connector |
|
Insert a Thin-bladed Screwdriver in this Direction |
|
Released in this Direction |
|
Protective Tape |
When the thin-bladed screwdriver with its tip wrapped with protective tape is inserted, the internal connector lock is released.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
Do not excessively insert the screwdriver. Otherwise, the internal connector terminals may become deformed or damaged.
Replace the instrument panel junction block assembly when the connector terminal, the locking section, or the case is damaged or deformed.
Hold the rib of the main body ECU (multiplex network body ECU).
|
Rotate in this Direction |
While rotating the main body ECU (multiplex network body ECU), completely release the lock.
|
Remove in this Direction |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.