Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0374972 FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a lifter motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction Lifter motor position sensor signal not received when power seat moved upward or downward.
·

Position control ECU assembly (driver seat)

·

Power seat lifter motor assembly (driver seat)

·

Harness or connector



WIRING DIAGRAM

B531523E05
2.198,0.438 2.354,0.635 0.156,0.198 10 false 1 2.198,0.948 2.354,1.146 0.156,0.198 10 false 4 2.198,1.458 2.354,1.656 0.156,0.198 10 false 2 2.198,1.99 2.354,2.188 0.156,0.198 10 false 3 0.781,2.458 1.792,2.688 1.01,0.229 10 false T12*1, S12*2 0.781,2.615 2.875,3.177 2.094,0.563 10 false Power Seat Lifter Motor Assembly (Driver Seat) 4.854,0.563 5.313,0.76 0.458,0.198 10 false S7 4.844,1.073 5.302,1.271 0.458,0.198 10 false S6 4.854,2.104 5.313,2.302 0.458,0.198 10 false S8 4.844,1.583 5.302,1.781 0.458,0.198 10 false S8 4.333,0.313 4.792,0.51 0.458,0.198 10 false 6*1 4.833,0.313 5.292,0.51 0.458,0.198 10 false 6*2 4.344,0.823 4.802,1.021 0.458,0.198 10 false 5*1 4.813,0.823 5.271,1.021 0.458,0.198 10 false 5*2 4.292,1.344 4.906,1.542 0.615,0.198 10 false 25*1 4.771,1.344 5.385,1.542 0.615,0.198 10 false 25*2 4.292,1.844 4.906,2.042 0.615,0.198 10 false 12*1 4.771,1.844 5.385,2.042 0.615,0.198 10 false 12*2 4.365,0.563 4.823,0.76 0.458,0.198 10 false T7 4.365,1.073 4.823,1.271 0.458,0.198 10 false T6 4.365,2.094 4.823,2.292 0.458,0.198 10 false T8 4.365,1.583 4.823,1.781 0.458,0.198 10 false T8 5.219,0.542 5.833,0.74 0.615,0.198 10 false LFT+ 5.219,1.031 5.833,1.229 0.615,0.198 10 false LFT- 5.208,1.552 5.823,1.75 0.615,0.198 10 false SSRL 5.219,2.104 5.833,2.302 0.615,0.198 10 false SGND 4.823,2.594 6.792,3.167 1.969,0.573 10 false Position Control ECU Assembly (Driver Seat) 4.125,3.385 5.813,3.583 1.688,0.198 10 false *1: for LHD 5.156,3.375 6.844,3.573 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>REGISTRATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2653 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (LIFTER OPERATION)
3.PERFORM ACTIVE TEST USING GTS (LIFTER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

6.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.
E407950C10
1.75,0.167 2.167,0.417 0.417,0.25 1.073,0.167 1.49,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.854,0.208 2.229,0.479 0.375,0.271 10 false S12 1.177,0.208 1.635,0.406 0.458,0.198 10 false T12 1.521,0.198 1.708,0.375 0.188,0.177 10 false *A 2.198,0.198 2.406,0.375 0.208,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Power Seat Lifter Motor Assembly [Driver Seat])


Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T12-2 - T12-3 Rear lifter switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S12-2 - S12-3 Rear lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

NG

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])
5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-25 (SSRL) - T12-2 Always Below 1 Ω
T8-25 (SSRL) or T12-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T12-3 Always Below 1 Ω
T8-12 (SGND) or T12-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-25 (SSRL) - S12-2 Always Below 1 Ω
S8-25 (SSRL) or S12-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S12-3 Always Below 1 Ω
S8-12 (SGND) or S12-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


b.

Inspect the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-6 (LFT+) - T12-1 Always Below 1 Ω
T7-6 (LFT+) or T12-1 - Other terminals and body ground Always 10 kΩ or higher
T6-5 (LFT-) - T12-4 Always Below 1 Ω
T6-5 (LFT-) or T12-4 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-6 (LFT+) - S12-1 Always Below 1 Ω
S7-6 (LFT+) or S12-1 - Other terminals and body ground Always 10 kΩ or higher
S6-5 (LFT-) - S12-4 Always Below 1 Ω
S6-5 (LFT-) or S12-4 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR