MALFUNCTION DESCRIPTION
The main CPU and sub CPU of the hybrid vehicle control ECU assembly monitor their internal operation and each other for malfunctions.
The cause of this malfunction may be the following:
Hybrid vehicle control ECU assembly malfunction
Discrepancy between motor resolver signal and actual vehicle speed
The hybrid vehicle control ECU assembly monitors its internal operation and will store these DTCs when it detects an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P060A94 | Hybrid/EV Powertrain Control Module Monitoring Processor Unexpected Operation | ·
The sub CPU value received by the main CPU of the hybrid vehicle control ECU assembly exceeds the threshold for a certain period of time. ·
The hybrid vehicle control ECU assembly detects an internal malfunction due to an abnormal calculation or sensor malfunction. (1 trip detection logic) |
Hybrid vehicle control ECU assembly | Comes on | Master Warning:
Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) and wait for 10 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P0A3F16 | Drive Motor "A" Position Sensor Circuit Voltage Below Threshold |
| P0A3F21 | Drive Motor "A" Position Sensor Signal Amplitude < Minimum | |
| P0A3F22 | Drive Motor "A" Position Sensor Signal Amplitude > Maximum | |
P060A94 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Relevant DTC | |
|---|---|
| C1464 | Front Speed Sensor RH Circuit |
| C1465 | Front Speed Sensor LH Circuit |
| C1466 | Rear Speed Sensor RH Circuit |
| C1467 | Rear Speed Sensor LH Circuit |
P060A94 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P060A94 only is output. | A |
| DTCs except P060A94 are output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P060A94.
| Result | Proceed to |
|---|---|
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) but "Vehicle Speed" was 3 km/h (2 mph) or more | A |
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) and "Vehicle Speed" was less than 3 km/h (2 mph) | B |
Turn the power switch off.
A
For the inspection method of the motor resolver circuit, refer to DTC P0A3F16.
B