When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.
Refer to the wiring diagram for the shift paddle switch circuit. (w/ Shift paddle switch)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift Position.
| Tester Display |
|---|
| Sports Shift Position |
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Sports Shift Position | Sports shift position | 0 to 255 | Shift lever in S, "+" or "-": 1 to 6
Shift lever in any position other than S, "+" and "-": 255 |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the shift lever operation. | A |
| The GTS display does not change according to the shift lever operation. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Sports Shift UP Signal, Sports Shift DOWN Signal.
| Tester Display |
|---|
| Sports Shift UP Signal |
| Sports Shift DOWN Signal |
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Sports Shift UP Signal | Operation of "+" transmission control switch. | ON or OFF | Shift lever held in "+" operated: ON
Shift lever in S: OFF |
| Sports Shift DOWN Signal | Operation of "-" transmission control switch. | ON or OFF | Shift lever held in "-" operated: ON
Shift lever in S: OFF |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the transmission control switch (shift lock control unit assembly) operation. | A |
| The GTS display does not change according to the transmission control switch (shift lock control unit assembly) operation. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G23 transmission control switch (shift lock control unit assembly) connector.
Turn the power switch on (IG).
| *a | Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-4 (IG) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-4 (IG) - Body ground | Power switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-2 (E) - Body ground | Power switch off | Below 1 Ω |
Reconnect the G23 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G23 transmission control switch (shift lock control unit assembly) connector.
| *A | for LHD |
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
for LHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-4 (IG) - G23-5 (S) | Shift lever in S
Shift lever held in "+" or "-" |
Below 1 Ω |
| G23-4 (IG) - G23-5 (S) | Shift lever in any position except S | 10 kΩ or higher |
| G23-3 (SFTU) - G23-2 (E) | Shift lever held in "+" | Below 1 Ω |
| G23-3 (SFTU) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| G23-1 (SFTD) - G23-2 (E) | Shift lever held in "-" | Below 1 Ω |
| G23-1 (SFTD) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| *A | for RHD |
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
for RHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-4 (IG) - G23-5 (S) | Shift lever in S
Shift lever held in "+" or "-" |
Below 1 Ω |
| G23-4 (IG) - G23-5 (S) | Shift lever in any position except S | 10 kΩ or higher |
| G23-1 (SFTU) - G23-2 (E) | Shift lever held in "+" | Below 1 Ω |
| G23-1 (SFTU) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| G23-3 (SFTD) - G23-2 (E) | Shift lever held in "-" | Below 1 Ω |
| G23-3 (SFTD) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
Reconnect the G23 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
Disconnect the G20 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Turn the power switch on (IG).
| *A | for LHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
for LHD:
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-25 (M) - Body ground | Power switch on (IG)
Shift lever in S, "+" or "-" |
11 to 14 V |
| Power switch on (IG)
Except shift lever in S, "+" and "-" |
Below 1 V |
If the power switch is turned on (IG) with the hybrid vehicle control ECU assembly connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.
| *A | for RHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
for RHD:
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-25 (M) - Body ground | Power switch on (IG)
Shift lever in S, "+" or "-" |
11 to 14 V |
| Power switch on (IG)
Except shift lever in S, "+" and "-" |
Below 1 V |
If the power switch is turned on (IG) with the hybrid vehicle control ECU assembly connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.
Turn the power switch off.
for LHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| A30-24 (SFTU) - Body ground | Shift lever in S | 10 kΩ or higher |
| A30-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| A30-11 (SFTD) - Body ground | Shift lever in S | 10 kΩ or higher |
for RHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| G63-24 (SFTU) - Body ground | Shift lever in S | 10 kΩ or higher |
| G63-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| G63-11 (SFTD) - Body ground | Shift lever in S | 10 kΩ or higher |
Reconnect the G20 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Reconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G23 transmission control switch (shift lock control unit assembly) connector.
| *A | for LHD |
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
for LHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-3 (SFTU) - G23-2 (E) | Shift lever held in "+" | Below 1 Ω |
| G23-3 (SFTU) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| G23-1 (SFTD) - G23-2 (E) | Shift lever held in "-" | Below 1 Ω |
| G23-1 (SFTD) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| *A | for RHD |
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
for RHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-1 (SFTU) - G23-2 (E) | Shift lever held in "+" | Below 1 Ω |
| G23-1 (SFTU) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
| G23-3 (SFTD) - G23-2 (E) | Shift lever held in "-" | Below 1 Ω |
| G23-3 (SFTD) - G23-2 (E) | Shift lever in S | 10 kΩ or higher |
Reconnect the G23 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
Disconnect the G20 spiral cable sub-assembly connector. (w/ Shift paddle switch)
| *A | for LHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
for LHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A30-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| Shift lever in S | 10 kΩ or higher | |
| A30-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| Shift lever in S | 10 kΩ or higher |
| *A | for RHD |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
for RHD:
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G63-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| Shift lever in S | 10 kΩ or higher | |
| G63-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| Shift lever in S | 10 kΩ or higher |
Reconnect the G20 spiral cable sub-assembly connector. (w/ Shift paddle switch)
Reconnect the A30*1, G63*2 hybrid vehicle control ECU assembly connector.
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG