Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE SYSTEM › from 2019.02
RM3620E _52 Drivetrain _076274 P710 HYBRID TRANSMISSION / TRANSAXLE _0371334 HYBRID TRANSAXLE SYSTEM G

P710 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345225

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the power switch on (IG).


PROCEDURE

Hide 53737D 1.REMOVE FRONT FENDER APRON SEAL LH

Hide 35162B 2.REMOVE TRANSAXLE CASE PROTECTOR (for 4WD/AWD)

a.
C382000C01
1.833,0.625 2.219,0.625 true 2.229,0.531 2.448,0.74 0.219,0.208 10 true *1
*1 Clip


Remove the 2 bolts.


b.

Remove the clip and transaxle case protector from the hybrid vehicle transaxle assembly.


Hide 3.INSPECT TRANSAXLE FLUID PRESSURE

NOTICE:

Make sure to perform the following inspection after inspecting and adjusting the engine.


a.
C393896

Remove the transmission oil pump cover plug from the hybrid vehicle transaxle assembly.


b.

Remove the O-ring from the transmission oil pump cover plug.


c.
C393897C01
1.365,1.854 1.615,1.854 true 2.833,0.917 2.917,0.583 2.917,0.583 3,0.583 false 2.333,0.417 2.667,0.417 2.667,0.417 2.667,0.833 false 2.458,0.417 2.458,0.833 false 1.646,1.781 1.979,1.99 0.333,0.208 10 true SST 3.031,0.5 3.344,0.698 0.313,0.198 10 false *2 2.177,0.344 2.375,0.573 0.198,0.229 10 false *1
*1 Gasket
*2 O-ring


Install SST to the hybrid vehicle transaxle assembly.

SST
09993-19015  (09993-00020, 09993-00040)


d.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Measure the hybrid transaxle fluid pressure.

Reference:
Maintenance Mode Engine Idle Speed Hybrid Transaxle Fluid Temperature Hybrid Transaxle Fluid Pressure
900 to 1000 rpm 20 to 50°C (68 to 122°F) 9.8 kPa (0.1 kgf/cm2, 1 psi) or more


NOTICE:

Be sure to cancel maintenance mode immediately after the hybrid transaxle fluid pressure check is completed.



f.

Remove SST from the hybrid vehicle transaxle assembly.


g.

Coat a new O-ring with ATF and install it to transmission oil pump cover plug.


h.

Install the transmission oil pump cover plug to the hybrid vehicle transaxle assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 35162B 4.INSTALL TRANSAXLE CASE PROTECTOR (for 4WD/AWD)

a.
C382001C01
1.833,0.635 2.229,0.635 true 2.24,0.531 2.469,0.74 0.229,0.208 10 true *1
*1 Clip


Install the transaxle case protector to the hybrid vehicle transaxle assembly with the clip.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
C382083C01
1.698,0.927 1.969,1.146 0.271,0.219 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the bolt.

Torque:
Specified Tightening Torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

8.8 N*m (90 kgf*cm, 78 in.*lbf)




Hide 53737D 5.INSTALL FRONT FENDER APRON SEAL LH