The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
12306
1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.
|
Bolt |
|
Nut |
Install the engine mounting insulator sub-assembly LH with the 2 bolts and nut.
Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).
Attach the claw to connect the engine room main wire.
Install the bolt.
89661
2.INSTALL ECM
12341
3.INSTALL ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Install the engine mounting spacer to the vehicle body with the 2 bolts.
Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).
12305
4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
|
Bolt |
|
Nut |
Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.
Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).
Install the bolt to connect the No. 2 ground wire.
Attach the clamps to install the radiator reserve tank assembly.
|
No. 6 Water By-pass Hose |
|
Bolt |
|
Nut |
Install the bolt and nut in the order shown in the illustration.
Connect the No. 6 water by-pass hose and attach the clamp.
| *1 | Suction Pipe Sub-assembly |
| *2 | Air Conditioning Tube And Accessory Assembly |
Attach the clamps to connect the suction pipe sub-assembly and air conditioning tube and accessory assembly.
Connect the connector.
G921A
5.INSTALL NO. 1 INVERTER RESERVE TANK BRACKET
Install the No. 1 inverter reserve tank bracket with the bolt.
6.INSTALL ENGINE HANGERS
7.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Remove the engine assembly from the engine stand.
19315
8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13405
9.INSTALL FLYWHEEL SUB-ASSEMBLY
31270
10.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
30900
11.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
11363A
12.INSTALL FLYWHEEL HOUSING SIDE COVER
28193
13.INSTALL STARTER HOLE INSULATOR
821H2
14.INSTALL HV AIR CONDITIONING WIRE
for 2WD:
Attach the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.
Install the bolt.
for 4WD/AWD:
Attach the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.
Install the 2 bolts.
| *a | Green-colored Lock |
|
Slide |
Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.
Make sure to wear insulated gloves.
Make sure that the connector is connected securely.
Attach the clamps.
82121
15.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
12371A
16.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
for LHD:
| *1 | Rear Engine Mounting Bracket |
| *2 | Rear Engine Mounting Insulator |
| *a | Protrusion |
| *b | Hole |
Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.
Attach the clamp to connect the engine wire.
for RHD:
| *1 | Rear Engine Mounting Bracket |
| *2 | Rear Engine Mounting Insulator |
| *a | Protrusion |
| *b | Hole |
Align the hole of the rear engine mounting insulator with the protrusion of the rear engine mounting bracket, slide the rear engine mounting insulator onto the rear engine mounting bracket to align the holes and install the rear engine mounting insulator with the bolt.
Attach the clamp to connect the engine wire.
82715
17.INSTALL WIRING HARNESS CLAMP BRACKET
for LHD:
Install the wiring harness clamp bracket with the bolt.
Attach the clamps to connect the engine wire.
for RHD:
Install the wiring harness clamp bracket with the bolt.
Attach the clamp to connect the engine wire.
12361
18.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION
51100H
19.INSTALL FRONT FRAME ASSEMBLY
11361J
20.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the cylinder block sub-assembly.
21.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
23825
22.INSTALL FUEL DELIVERY GUARD
Install the fuel delivery guard to the engine mounting bracket RH with the bolt.
23.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Perform inspection after repair after replacing the engine assembly.
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
w/o Canister Pump Module:
Set the engine assembly with transaxle on an engine lifter.
|
Attachments | - | - |
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
| *1 | Front Bumper Extension Sub-assembly LH |
| *2 | Front Bumper Extension Sub-assembly RH |
| *3 | Rear Front Suspension Member Brace LH |
| *4 | Rear Front Suspension Member Brace RH |
|
Bolt |
|
Nut |
Install the front bumper extension sub-assembly LH and front bumper extension sub-assembly RH to the front frame assembly and vehicle body with the 2 bolts (A), 2 bolts (B) and 4 nuts.
Install the rear front suspension member brace LH and rear front suspension member brace RH to the front frame assembly and vehicle body with the 2 bolts (C) and 4 bolts (D).
Install the engine mounting insulator sub-assembly LH to the hybrid vehicle transaxle assembly with the 4 bolts.
Tighten the 4 bolts in the order of (A), (C), (B) and (D).
Install the engine mounting stay LH to the engine mounting insulator sub-assembly LH with the 3 bolts.
Temporarily install the bolt (A), and then tighten the 3 bolts in the order of (B), (C) and (A).
|
Bolt |
|
Nut |
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.
45220
24.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
43420
25.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
26.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
48069
27.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
28.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45470
29.CONNECT TIE ROD ASSEMBLY LH
45460
30.CONNECT TIE ROD ASSEMBLY RH
Use the same procedure described for the LH side.
48810
31.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
32.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
89543
33.CONNECT FRONT SPEED SENSOR LH
89542
34.CONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
43502H
35.INSTALL FRONT AXLE SHAFT NUT LH
43501H
36.INSTALL FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
43502H
37.STAKE FRONT AXLE SHAFT NUT LH
43501H
38.STAKE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
17410
39.INSTALL FRONT EXHAUST PIPE ASSEMBLY
58165C
40.INSTALL FRONT FLOOR COVER RH
|
Bolt |
|
Screw |
|
Clip |
Attach the clips to install the front floor cover RH.
Install the 2 bolts, 3 screws and clip.
58166A
41.INSTALL FRONT FLOOR COVER LH
|
Bolt |
|
Screw |
|
Clip |
Attach the clips to install the front floor cover LH.
Install the 2 bolts, 4 screws and clip.
51468B
42.INSTALL ENGINE UNDER COVER HEAT INSULATOR
Install the engine under cover heat insulator with the 2 clips.
43.CONNECT WIRE HARNESS
Install the 2 bolts to connect the ground wires.
Attach the clamp.
|
Nut |
|
Connector |
Attach the claw to connect the wire harness to the engine room relay block and junction block assembly.
Connect the connectors to the engine room relay block and junction block assembly.
Install the nut to the engine room relay block and junction block assembly.
Attach the claws and remove the No. 2 relay block cover.
G9229A
44.CONNECT NO. 5 INVERTER COOLING HOSE
Connect the No. 5 inverter cooling hose to the motor cooling cooler, and slide the clip to secure the hose.
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 5 inverter cooling hose is securely inserted to the stopper.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | Front Side | *f | 2 to 7 mm (0.0787 to 0.276 in.) |
88704
45.CONNECT SUCTION HOSE SUB-ASSEMBLY
88711
46.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
16572D
47.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 2 radiator hose is securely inserted to the stopper.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Upper Side |
| *e | RH Side | *f | 2 to 7 mm (0.0787 to 0.276 in.) |
16571C
48.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the water outlet, and slide the clip to secure the hose.
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 1 radiator hose is securely inserted to the stopper.
Attach the clamp.
| *a | View A | *b | 120° |
| *c | Paint Mark | *d | Front Side |
| *e | RH Side | *f | 2 to 7 mm (0.0787 to 0.276 in.) |
87245
49.CONNECT INLET HEATER WATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusions of the inlet heater water hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and securely insert the inlet heater water hose connector to the stopper of the pipe.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the flow shutting valve (water by-pass hose assembly) and inlet heater hose connector are securely connected by pulling on them.
87246
50.CONNECT OUTLET HEATER WATER HOSE
| *a | Protrusion |
| *b | Cutout |
Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater water hose connector and securely insert the outlet heater water hose connector to the stopper of the pipe.
| *a | Retainer |
|
Push |
|
Push in |
Push in the retainer.
Check that the No. 2 water by-pass pipe sub-assembly and outlet heater hose connector are securely connected by pulling on them.
23901
51.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly.
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube connector.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
23826
52.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the purge VSV.
Attach the clamp.
16282
53.INSTALL NO. 5 WATER BY-PASS HOSE
Install the No. 5 water by-pass hose to the No. 3 water by-pass pipe and radiator assembly, and slide the clips to secure the hose.
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 5 water by-pass hose is securely inserted to the stopper.
| *a | View A | *b | View B |
| *c | 360° | *d | 120° |
| *e | Paint Mark | *f | Upper Side |
| *g | Front Side | *h | Rear Side |
| *i | 2 to 7 mm (0.0787 to 0.276 in.) | - | - |
G92A0A
54.INSTALL INVERTER RESERVE TANK ASSEMBLY
Connect the No. 2 inverter cooling hose and No. 5 inverter cooling hose to the inverter reserve tank assembly, and slide the clips to secure the hoses.
Align the direction of the claw on the clip with the paint mark on the hose.
Make sure the No. 2 inverter cooling hose and No. 5 inverter cooling hose are securely inserted to the stopper.
| *a | View A | *b | View B |
| *c | 120° | *d | Paint Mark |
| *e | Upper Side | *f | RH Side |
| *g | 2 to 7 mm (0.0787 to 0.276 in.) | - | - |
| *a | Pin |
| *b | Grommet |
Fit the pin of the inverter reserve tank assembly into grommet as shown in the illustration.
Install the inverter reserve tank assembly with the 2 bolts.
G9200
55.INSTALL INVERTER WITH CONVERTER ASSEMBLY
56.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
17750A
57.INSTALL INLET AIR CLEANER ASSEMBLY
12601B
58.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
for LHD:
Attach the clips to install the No. 1 engine cover sub-assembly.
Securely attach the clips.
If the clips are forcibly attached or struck with an object, they may be damaged.
for RHD:
Attach the clips to install the No. 1 engine cover sub-assembly.
Securely attach the clips.
If the clips are forcibly attached or struck with an object, they may be damaged.
52132A
59.INSTALL FRONT BUMPER NO. 2 REINFORCEMENT
52618
60.INSTALL FRONT LOWER BUMPER ABSORBER
Attach the claws to install the front lower bumper absorber.
Install the clip.
61.INSTALL HEADLIGHT ASSEMBLY LH
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>INSTALLATION
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>INSTALLATION
62.INSTALL FRONT BUMPER ASSEMBLY
53737D
63.INSTALL FRONT FENDER APRON SEAL LH
|
Bolt |
|
Clip |
Install the front fender apron seal LH with the 2 bolts and clip.
53736E
64.INSTALL FRONT FENDER APRON SEAL RH
|
Bolt |
|
Clip |
Install the front fender apron seal RH with the 2 bolts and clip.
51420
65.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
|
Bolt |
|
Screw |
|
Clip |
Install the No. 2 engine under cover assembly with the 2 bolts, 2 screws and 6 clips.
51441
66.INSTALL NO. 1 ENGINE UNDER COVER
Attach the guide to install the No. 1 engine under cover.
Install the 2 bolts and 10 screws. (Short Type Front Fender Front Splash Shield)
Install the 2 bolts and 8 screws. (Long Type Front Fender Front Splash Shield)
| *a | Short Type Front Fender Front Splash Shield | - | - |
|
Bolt |
|
Screw |
53896B
67.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
for Short Type:
Attach the clip to install the front fender front splash shield LH.
Install the 3 screws.
for Long Type:
Attach the clip to install the front fender front splash shield LH.
Install the 4 screws.
53895B
68.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
for Short Type:
Attach the clip to install the front fender front splash shield RH.
Install the 3 screws.
for Long Type:
Attach the clip to install the front fender front splash shield RH.
Install the 4 screws.
G3834
69.INSTALL SERVICE PLUG GRIP
58441J
70.INSTALL BATTERY SERVICE HOLE COVER
71.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
65351A
72.INSTALL BATTERY HOLE COVER
58416K
73.INSTALL REAR NO. 2 FLOOR BOARD
58410B
74.INSTALL DECK BOARD ASSEMBLY
75.INSPECT SHIFT LEVER POSITION
76.ADJUST SHIFT LEVER POSITION
77.ADD ENGINE OIL
78.ADD HYBRID TRANSAXLE FLUID
79.INSPECT HYBRID TRANSAXLE FLUID
80.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
81.ADD ENGINE COOLANT (for Engine)
82.WARM UP COMPRESSOR
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
83.INSPECT FOR ENGINE OIL LEAK
84.INSPECT FOR COOLANT LEAK (for Engine)
85.INSPECT FOR REFRIGERANT LEAK
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
86.INSPECT FOR FUEL LEAK
87.INSPECT FOR EXHAUST GAS LEAK
88.CHECK ENGINE OIL LEVEL
89.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR
90.INSTALL FRONT WHEELS
91. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
92.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
93.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
94.INSPECT IGNITION TIMING
95.INSPECT ENGINE IDLE SPEED
96.INSPECT CO/HC
97.CHECK SPEED SENSOR SIGNAL