Home › Engine / Hybrid System › A25B-FXS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2019.02
RM3620E _51 Engine / Hybrid System _080120 A25B-FXS INTAKE / EXHAUST _0388960 INTAKE MANIFOLD A

A25B-FXS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22030 1.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25620 2.REMOVE EGR VALVE ASSEMBLY

Hide 89421 3.REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 25860 4.REMOVE PURGE VALVE (PURGE VSV)

Hide 82121 5.DISCONNECT ENGINE WIRE

a.
A405766

Disconnect the No. 5 engine wire connector.


b.

Remove the bolt and disconnect the engine wire from the cylinder head sub-assembly.


c.
A433918

Remove the bolt.


d.

Detach the wire harness clamp and disconnect the engine wire from the intake manifold.


Hide 16279 6.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A402291

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


b.

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A402290N02
0.844,1.792 0.99,1.958 0.146,0.167 10 true A 2.104,1.969 2.271,2.135 0.167,0.167 10 true B 1.281,0.344 1.438,0.521 0.156,0.177 10 true A

Detach the wire harness clamp and disconnect the HV air conditioning wire.


b.

Using an 8 mm socket wrench, remove the 2 bolts (A) and separate the No. 2 water by-pass pipe from the intake manifold.


c.

Remove the bolt (B) and No. 2 water by-pass pipe from the cylinder block sub-assembly.


Hide 23820 8.REMOVE NO. 2 FUEL VAPOR FEED HOSE

a.
A402292

Remove the No. 2 fuel vapor feed hose from the intake manifold.


Hide 17111 9.REMOVE INTAKE MANIFOLD

a.
A433919

w/o Stud Bolt:

i.

Remove the 5 bolts and intake manifold from the cylinder head sub-assembly.



b.
A436576C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


w/ Stud Bolt:

i.

Remove the 3 bolts, 2 nuts and intake manifold from the cylinder head sub-assembly.



Hide 17177 10.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A402294

Remove the No. 1 intake manifold to head gasket from the intake manifold.


Hide 12611B 11.REMOVE NO. 1 ENGINE COVER

a.
A402295

Remove the clip and No. 1 engine cover.


Hide 12.REMOVE VACUUM HOSE

a.
A402296

Remove the vacuum hose from the intake manifold.