Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2019.02–2020.08
RM3620E _51 Engine / Hybrid System _076482 A25A-FXS INTAKE / EXHAUST _0372157 EXHAUST MANIFOLD A

A25A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 6 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold, No. 1 exhaust manifold heat insulator and No. 1 upper front floor heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A402303N02
1.573,0.969 1.729,1.167 0.156,0.198 10 false 1 2.073,0.698 2.229,0.896 0.156,0.198 10 true 1 1.125,0.083 1.271,0.25 0.146,0.167 10 true 2 2.469,0.063 2.615,0.25 0.146,0.188 10 true 3 1.594,0.698 1.74,0.885 0.146,0.188 10 true 4 2.719,0.292 2.854,0.469 0.135,0.177 10 true 5 0.99,0.76 1.125,0.927 0.135,0.167 10 true 6 0.542,0.24 0.677,0.406 0.135,0.167 10 true 7

Using a 12 mm deep socket wrench, temporarily install the exhaust manifold to the cylinder head sub-assembly with 7 new nuts.


d.

Using the 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A402302N02
2.771,1.427 2.927,1.625 0.156,0.198 10 true 1 0.375,1.063 0.531,1.26 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402305C02
2.365,0.417 2.573,0.615 0.208,0.198 10 true *a
*a Torque Wrench Fulcrum Length


w/o GPF:

i.

Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)





b.

w/ GPF:

i.

Using a 10 mm union nut wrench, install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
Specified tightening torque : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)





Hide 58151 5.INSTALL NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

a.

Install the No. 1 upper front floor heat insulator to the vehicle body with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 25706 6.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

a.
A445028C01
1.615,0.219 1.844,0.438 0.229,0.219 10 true *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).




b.

Install the nut and connect the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the vacuum transmitting hose assembly to the No. 1 tube and slide the clip to secure it.


Hide 7.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 89467B 8.INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install 2 new gaskets to the front exhaust pipe assembly.


b.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly to the exhaust manifold and tail exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.
A432694C01
2.542,0.479 2.625,0.208 2.625,0.208 2.75,0.208 true 2.198,0.719 2.448,0.938 2.448,0.938 2.615,0.729 true 2.771,0.115 2.958,0.313 0.188,0.198 10 true *a 2.385,0.958 2.573,1.135 0.188,0.177 10 true *b
*a Tie Band
*b Wire Harness Clamp


Connect the air fuel ratio sensor connector.


e.

Attach the 2 wire harness clamps so that the tie band is positioned as shown in the illustration.


Hide 51468B 11.INSTALL ENGINE UNDER COVER HEAT INSULATOR

Hide 51420 12.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY