53158E
1.INSTALL NO. 4 RADIATOR GRILLE SEAL (for RH Side)
When installing a new No. 4 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 4 radiator grille seal trying not to touch the adhesional surface.
| *a | Rib |
Install the No. 4 radiator grille seal as shown in the illustration.
53156G
2.INSTALL NO. 2 RADIATOR GRILLE SEAL
When installing a new No. 2 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 2 radiator grille seal trying not to touch the adhesional surface.
| *1 | No. 4 Radiator Grille Seal (RH Side) |
| *a | Rib |
Install the No. 2 radiator grille seal as shown in the illustration.
53158E
3.INSTALL NO. 4 RADIATOR GRILLE SEAL (for LH Side)
When installing a new No. 4 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 4 radiator grille seal trying not to touch the adhesional surface.
| *1 | No. 2 Radiator Grille Seal |
| *a | Line |
| *b | 0 to 3 mm (0 to 0.118 in.) |
Install the No. 4 radiator grille seal as shown in the illustration.
53155J
4.INSTALL NO. 1 RADIATOR GRILLE SEAL
When installing a new No. 1 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 1 radiator grille seal trying not to touch the adhesional surface.
| *a | Rib |
Install the No. 1 radiator grille seal as shown in the illustration.
53157C
5.INSTALL NO. 3 RADIATOR GRILLE SEAL (for LH Side)
When installing a new No. 3 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 3 radiator grille seal trying not to touch the adhesional surface.
| *1 | No. 1 Radiator Grille Seal |
| *a | Frame Terminal Part |
| *b | 0 to 3 mm (0 to 0.118 in.) |
Install the No. 3 radiator grille seal as shown in the illustration.
53157C
6.INSTALL NO. 3 RADIATOR GRILLE SEAL (for RH Side)
When installing a new No. 3 radiator grille seal, heat the radiator grille shutter sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Radiator Grille Shutter Sub-assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the radiator grille shutter sub-assembly excessively.
When reusing the radiator grille shutter sub-assembly:
Using a heat light, heat the radiator grille shutter sub-assembly surface.
Remove any remaining double-sided tape from the radiator grille shutter sub-assembly.
Wipe off any tape adhesive residue with cleaner.
Installing the radiator grille shutter sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Clean the new radiator grille shutter sub-assembly surface.
Remove the release paper of a new No. 3 radiator grille seal trying not to touch the adhesional surface.
| *1 | No. 1 Radiator Grille Seal |
| *a | Frame Terminal Part |
Install the No. 3 radiator grille seal as shown in the illustration.
88940D
7.INSTALL SWING GRILLE ACTUATOR ASSEMBLY
When installing a new swing grille actuator assembly:
Open the grille shutter fin as shown in the illustration.
for Type A:
|
Install in this Direction |
Install the swing grille actuator assembly as shown in the illustration.
for Type B:
|
Install in this Direction |
Install the swing grille actuator assembly as shown in the illustration.
Connect the connector.
85667F
8.INSTALL MOTOR COVER
|
Install in this Direction |
Attach the claw to install the motor cover as shown in the illustration.
88790B
9.INSTALL THERMISTOR ASSEMBLY